Home › Power Source / Network › POWER DISTRIBUTION › FUSIBLE LINK (for 120A DC/DC) › from 2021.02
RM33C0E _57 Power Source / Network _065453 POWER DISTRIBUTION _0489191 FUSIBLE LINK(for 120A DC/DC) A

POWER DISTRIBUTION  FUSIBLE LINK(for 120A DC/DC)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during fusible link block assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Tracing Assist System (Click here)
Pre-collision System
Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic View Monitor System (Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 64718C 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 12601B 4.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 53295E 5.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 6.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 7.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 82662B 9.REMOVE NO. 2 RELAY BLOCK COVER

a.
E473454

Disengage the 2 claws and remove the No. 2 relay block cover.


Hide 82663 10.REMOVE RELAY BLOCK LOWER COVER

a.
E473455

Disengage the clamp and 2 claws.


b.
E473456

Remove the nut.


c.

Disconnect the 5 connectors.


d.
E473457

Disengage the claw and separate the wire harness.


e.
E473458

Remove the 2 bolts and nut.


f.

Remove the wiring harness clamp and separate the wire harness.

E473460C01
4.74,0.115 5.115,0.354 0.375,0.24 12 false *A 4.74,1.5 5.115,1.74 0.375,0.24 12 false *B
*A for LHD *B for RHD



g.
E473459

Remove the tape.


h.

Using a screwdriver with its tip wrapped in protective tape, disengage the 9 claws to remove the relay block lower cover.

E473461C01
1.406,4 1.792,4.302 true 2.969,0.698 3.521,0.76 true 5.5,1.021 5.198,1.5 true 1.781,4.313 2.094,4.51 0.313,0.198 10 false *a 3.542,0.667 3.854,0.865 0.313,0.198 10 false *a 5.083,1.51 5.396,1.708 0.313,0.198 10 false *a
*a Protective Tape - -



Hide 82620A 11.REMOVE FUSIBLE LINK BLOCK ASSEMBLY

a.

Using a screwdriver with its tip wrapped in protective tape, disengage the 7 claws to separate the fuse block assembly from the engine room relay block assembly as shown in the illustration.

E473463C01
1.365,0.292 1.833,0.469 true 1.125,0.167 1.354,0.354 0.229,0.188 10 true *a
*a Protective Tape - -
V113147

Separate in this Direction - -



b.
E473465

Disengage the 6 claws and disconnect the 3 connectors.


c.
E473466

Remove the 4 bolts and disconnect the 4 wire harnesses.


d.
E473467C01
0,0 0,0 false
V113147

Remove in this Direction


Disconnect the connector and remove the fusible link block assembly as shown in the illustration.