Home › Engine / Hybrid System › CRUISE CONTROL › LANE TRACING ASSIST SYSTEM › from 2022.01
RM33C0E _51 Engine / Hybrid System _065434 CRUISE CONTROL _0465300 LANE TRACING ASSIST SYSTEM J

CRUISE CONTROL  LANE TRACING ASSIST SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The forward recognition camera receives LTA switch signals from the steering pad switch assembly.

WIRING DIAGRAM

E446505E19
1.646,1.646 3.177,1.844 1.531,0.198 10 false LTA Switch 1.021,2.073 3.031,2.323 2.01,0.25 10 false Steering Pad Switch Assembly 3.063,2.063 4.167,2.5 1.104,0.438 10 false Spiral Cable Sub-assembly 5.031,2.167 7.021,2.354 1.99,0.188 10 false Forward Recognition Camera 4.052,0.906 4.51,1.104 0.458,0.198 10 false K22 4.042,1.521 4.5,1.719 0.458,0.198 10 false K22 2.917,0.917 3.375,1.115 0.458,0.198 10 false z1 2.917,1.51 3.375,1.708 0.458,0.198 10 false z1 3.427,0.813 4.042,1.01 0.615,0.198 10 false DIST 3.417,1.417 4.031,1.615 0.615,0.198 10 false ECC 5.031,2.01 5.417,2.229 0.385,0.219 10 false V24 5.375,0.917 5.875,1.115 0.5,0.198 10 false LKSW 5.198,0.823 5.51,1.021 0.313,0.198 10 false 3 4.125,0.719 4.438,0.917 0.313,0.198 10 false 6 4.125,1.323 4.438,1.521 0.313,0.198 10 false 2 2.896,1.323 3.208,1.521 0.313,0.198 10 false 12 2.948,0.719 3.26,0.917 0.313,0.198 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT


·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (Lane Control)
a.

Read the Data List according to the display on the GTS.

Chassis > Lane Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
LDA Control Whether lane tracing assist system control is permitted or not Prohibit or Permit Prohibit: Lane tracing assist system control not possible
Permit: Lane tracing assist system control possible
-
Chassis > Lane Control > Data List
Tester Display
LDA Control
50003 418 3

Result:
Result Proceed to
The value of the Data List item changes in accordance with the operation of the LTA switch A
The value of the Data List item does not change in accordance with the operation of the LTA switch B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the V24 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-6 (DIST) - V24-3 (LKSW) Always Below 1 Ω
K22-6 (DIST) or V24-3 (LKSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-2 (ECC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR