Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM D

N04C-UH ENGINE CONTROL  ECD SYSTEM  DIAGNOSIS SYSTEM  


DESCRIPTION


A093827


When troubleshooting Euro-OBD vehicles, the vehicle must be connected to the intelligent tester. Various data output from the vehicle's Engine Control Module (ECM) can then be read.

The Malfunction Indicator Lamp (MIL) is illuminated when the vehicle's on-board computer detects a malfunction in the computer itself or in drive system components. In addition, the applicable Diagnostic Trouble Codes (DTCs) are recorded in the ECM memory (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)

If the malfunction does not recur, the MIL stays ON until the ignition switch is turned off, and then the MIL turns off when the ignition switch is turned ON. Be aware that the DTCs remain recorded in the ECM memory.

To check the DTCs, connect the intelligent tester to the DLC3 on the vehicle.

NORMAL MODE AND CHECK MODE


The diagnosis system operates in "normal mode" during normal vehicle use. In normal mode, "2 trip detection logic" is used to ensure accurate detection of malfunctions. "Check mode" is also available to technicians as an option. In check mode, "1 trip detection logic" is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


2 TRIP DETECTION LOGIC


When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the next subsequent drive cycle, the MIL is illuminated (2nd trip).


FREEZE FRAME DATA


The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


DLC3 (Data Link Connector 3)


A122830E72
2.427,1.635 2.865,1.76 false 1.604,1.052 0.969,0.552 false 1.813,1.031 1.365,0.438 false 1.99,1.042 2.167,0.417 false 2.229,1.042 2.698,0.604 false 1.99,1.635 2.063,1.948 false 2.323,1.469 2.51,1.625 0.188,0.156 10 false 16 2.115,1.469 2.302,1.625 0.188,0.156 10 false 15 1.906,1.469 2.094,1.625 0.188,0.156 10 false 14 1.708,1.469 1.896,1.625 0.188,0.156 10 false 13 1.5,1.469 1.688,1.625 0.188,0.156 10 false 12 1.302,1.469 1.479,1.625 0.177,0.156 10 false 11 1.094,1.469 1.281,1.625 0.188,0.156 10 false 10 0.938,1.469 1.042,1.625 0.104,0.156 10 false 9 0.938,1.042 1.042,1.198 0.104,0.156 10 false 1 1.146,1.042 1.25,1.198 0.104,0.156 10 false 2 1.354,1.042 1.458,1.198 0.104,0.156 10 false 3 1.552,1.042 1.656,1.198 0.104,0.156 10 false 4 1.76,1.042 1.865,1.198 0.104,0.156 10 false 5 1.969,1.042 2.073,1.198 0.104,0.156 10 false 6 2.167,1.042 2.271,1.198 0.104,0.156 10 false 7 2.375,1.042 2.479,1.198 0.104,0.156 10 false 8 0.135,0.115 0.531,0.271 0.396,0.156 10 false DLC3 2.698,0.406 2.958,0.604 0.26,0.198 10 false SIL 1.969,0.188 2.406,0.354 0.438,0.167 10 false CANH 1.177,0.229 1.406,0.375 0.229,0.146 10 false SG 0.75,0.385 1.021,0.531 0.271,0.146 10 false CG 1.927,1.969 2.396,2.135 0.469,0.167 10 false CANL 2.958,1.698 3.271,1.865 0.313,0.167 10 false BAT

The vehicle's ECM uses ISO 15765-4 for communication protocol. The terminal arrangement of the DLC3 complies with ISO 15031-03 and matches the ISO 15765-4 format.

HINT:

Connect the cable of the intelligent tester to the DLC3, turn the ignition switch to ON and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.

If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.

If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.


Symbols (Terminal No.) Terminal Description Condition Result
SIL (7) - SG (5) Bus "+" line During transmission Pulse generation
CG (4) - Body ground Chassis ground Always Below 1 Ω
SG (5) - Body ground Signal ground Always Below 1 Ω
BAT (16) - Body ground Battery positive Always 11 to 14 V
CANH (6) - CANL (14) CAN bus line Ignition switch off 54 to 69 Ω
CANH (6) - CG (4) HIGH-level CAN bus line Ignition switch off 200 Ω or higher
CANL (14) - CG (4) LOW-level CAN bus line Ignition switch off 200 Ω or higher
CANH (6) - BAT (16) HIGH-level CAN bus line Ignition switch off 6 kΩ or higher
CANL (14) - BAT (16) LOW-level CAN bus line Ignition switch off 6 kΩ or higher

NOTICE:

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors.

If the result is not as specified, the DLC3 may have a malfunction. Repair or replace the harness or connector.



INSPECT BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


CHECK MIL


A093827

a.

The MIL will be illuminated when the ignition switch is turned ON and the engine is not running.

HINT:

If the MIL is not illuminated, check the MIL circuit (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>MIL Circuit).



b.

When the engine is started, the MIL should turn off.

If the lamp remains on, the diagnosis system has detected a malfunction or abnormality in the ECD system.



ALL READINESS


HINT:
·

With "All Readiness" you can check whether or not the DTC judgment has been completed by using the intelligent tester.

·

Check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.



e.

Turn the ignition switch off and wait for 30 seconds or more.


f.

Perform the DTC judgment driving pattern to run the DTC judgment.


g.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


h.

Input the DTCs to be confirmed.


i.

Check the DTC judgment result.

Result:
Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System normal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving after confirming DTC enabling conditions


UNKNOWN
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit