Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM J

N04C-UH ENGINE CONTROL  ECD SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM. By turning the ignition switch to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should illuminate and should then turn off. If the MIL remains illuminated or does not illuminate, conduct the following troubleshooting procedure. If the ECM detects any trouble, the MIL illuminates. At this time, the ECM records a DTC in the memory.

WIRING DIAGRAM

A403470E04
0.042,1.281 1.042,1.635 1,0.354 10 false From IG2-NO. 2 Relay 1.896,1.583 2.708,1.76 0.813,0.177 10 false METER-IG2 3.427,1.885 4.677,2.063 1.25,0.177 10 false Combination Meter 3.073,1.427 3.302,1.615 0.229,0.188 10 false J1 4.76,1.427 4.99,1.615 0.229,0.188 10 false J1 3.083,1.219 3.26,1.406 0.177,0.188 10 false 2 4.75,1.229 4.958,1.417 0.208,0.188 10 false 24 3.344,1.292 3.625,1.479 0.281,0.188 10 false IG+ 3.708,1.604 3.99,1.792 0.281,0.188 10 false MIL 4.313,1.313 4.646,1.51 0.333,0.198 10 false CHK 5.927,2.167 6.292,2.365 0.365,0.198 10 false A54 5.917,2.323 6.302,2.521 0.385,0.198 10 false ECM 5.625,1.406 5.844,1.594 0.219,0.188 10 false W 5.396,1.292 5.563,1.49 0.167,0.198 10 false 9

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK THAT MIL ILLUMINATES
a.

Turn the ignition switch to ON.


b.

Check the illumination of the MIL.


Result:
Result Proceed to
MIL remains illuminated (Even after ignition switch is turned to ON and several seconds have passed, MIL still remains illuminated) A
MIL remains off (Does not illuminate at all) B
MIL illuminates for several seconds, but turns off after engine is started C



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK IF ENGINE STARTS

C

2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Check if any DTCs have been stored. Note any DTCs.



g.

Check if the MIL goes off.


Result:
Result Proceed to
MIL goes off A
MIL does not go off B



A

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

B

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A065748E68
2.448,0.427 2.802,0.667 0.354,0.24 2.51,0.469 2.813,0.667 0.302,0.198 10 false A54 0.115,0.083 0.417,0.281 0.302,0.198 10 false *a

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check if the MIL is illuminated.

Result:
Result Proceed to
MIL is not illuminated A
MIL is illuminated B


Text in Illustration
*a Rear view of wire harness connector
(to ECM)



A

B

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J1-24 (CHK) or A54-9 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

5.CHECK IF ENGINE STARTS
a.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

6.CHECK HARNESS AND CONNECTOR (ECM TERMINAL VOLTAGE)

B

6.CHECK HARNESS AND CONNECTOR (ECM TERMINAL VOLTAGE)
a.
A065748E69
2.438,0.427 2.802,0.667 0.365,0.24 2.781,1.292 2.969,1.552 true 2.49,0.458 2.823,0.646 0.333,0.188 10 false A54 2.896,1.573 3.323,1.771 0.427,0.198 10 false 9 (W) 0.104,0.073 0.344,0.271 0.24,0.198 10 false *a

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A54-9 (W) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)


Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J1-24 (CHK) - A54-9 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)