Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P0560  System Voltage  


DESCRIPTION

While the ignition switch is off, battery voltage is supplied to terminal BATT of the ECM for storing DTCs and fuel injection feedback learning values.

DTC No. DTC Detection Condition Trouble Area
P0560 Condition (a) or (b) continues:
(1 trip detection logic)
(a) Significant decrease in battery voltage
(b) Open in back-up power source circuit
·

Open in back-up power source circuit

·

Low battery voltage

·

ECM



HINT:

If DTC P0560 appears, the ECM does not store other DTCs.


WIRING DIAGRAM

A398545E04
0.688,0.99 1.333,1.177 0.646,0.188 10 false FL MAIN 1.229,0.656 2.042,0.844 0.813,0.188 10 false R/B NO. 2-B 2.802,0.667 3.073,0.844 0.271,0.177 10 false P/I 3.885,0.656 4.563,0.854 0.677,0.198 10 false EFI-MAIN 1.323,1.948 2,2.146 0.677,0.198 10 false Battery 5.396,1.354 5.74,1.531 0.344,0.177 10 false B60 5.385,0.479 5.729,0.656 0.344,0.177 10 false A52 5.792,0.365 6.198,0.531 0.406,0.167 10 false BATT 5.813,1.354 6.063,1.531 0.25,0.177 10 false E1 6.167,2.052 6.563,2.24 0.396,0.188 10 false ECM 5.479,0.271 5.646,0.448 0.167,0.177 10 false 2 5.479,1.167 5.646,1.344 0.167,0.177 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of this circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT ECM (BATT VOLTAGE)
a.
A224395E31
1.969,0.198 2.385,0.438 0.417,0.24 1.323,0.198 1.74,0.438 0.417,0.24 0.854,1.531 1.167,0.781 true 1.969,1.542 2.271,0.792 true 0.104,0.052 0.375,0.302 0.271,0.25 10 false *a 1.396,0.24 1.698,0.417 0.302,0.177 10 false B60 0.604,1.573 1.146,1.781 0.542,0.208 10 false 7 (E1) 1.688,1.573 2.333,1.771 0.646,0.198 10 false 2 (BATT) 2.052,0.24 2.354,0.417 0.302,0.177 10 false A52

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A52-2 (BATT) - B60-7 (E1) Always 11 to 14 V


Text in Illustration
*a Rear view of wire harness connector
(to ECM)


c.

Reconnect the ECM connector.


Result:
Result Proceed to
NG A
OK B



A

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

B

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the negative battery terminal.


b.

Disconnect the positive battery terminal.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A52-2 (BATT) - Positive battery terminal Always Below 1 Ω
A52-2 (BATT) or Positive battery terminal - Body ground Always 10 kΩ or higher



e.

Reconnect the ECM connector.


f.

Reconnect the positive battery terminal.


g.

Reconnect the negative battery terminal.


Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE BATTERY