Home › Engine / Hybrid System › N04C-UH (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073137 N04C-UH ENGINE CONTROL _0355844 ECD SYSTEM C

N04C-UH ENGINE CONTROL  ECD SYSTEM  P1425  Differential Pressure Sensor Circuit  P1427  Differential Pressure Sensor Circuit Low  P1428  Differential Pressure Sensor Circuit High  


DESCRIPTION

A187357E02
2.469,1.698 2.323,1.698 2.323,1.698 2.146,2.51 true 2.583,4.104 2.417,4.104 2.417,4.104 2.302,3.625 true 6.146,1.948 6.26,1.948 6.26,1.948 6.385,1.594 true 5.594,2.75 5.469,2.75 5.469,2.75 5.302,3.573 false 4.5,1.635 4.448,1.635 false 4.51,1.677 4.448,1.813 false 0.677,1.49 1.052,1.677 0.375,0.188 10 false ECM 2.521,1.625 3.802,1.969 1.281,0.344 10 false Differential Pressure Sensor 2.635,4.031 4.177,4.24 1.542,0.208 10 false DPF Catalytic Converter 0.135,3.385 0.698,3.729 0.563,0.344 10 false Exhaust Gas 4.031,0.365 6.021,0.771 1.99,0.406 10 false Property of Output Voltage: 3.271,0.979 5.792,1.156 2.521,0.177 10 false Differential Pressure Sensor Voltage (V) 4.073,1.396 4.469,1.552 0.396,0.156 10 false 5.000 4.073,1.552 4.469,1.708 0.396,0.156 10 false 4.800 4.083,1.813 4.479,1.969 0.396,0.156 10 false 4.700 4.094,2.854 4.49,3.01 0.396,0.156 10 false 1.530 4.094,3.063 4.49,3.219 0.396,0.156 10 false 0.750 4.094,3.219 4.49,3.375 0.396,0.156 10 false 0.530 4.094,3.427 4.49,3.583 0.396,0.156 10 false 0.400 4.521,3.719 4.792,3.875 0.271,0.156 10 false -0.5 5.031,3.729 5.354,3.885 0.323,0.156 10 false 20.0 6.458,3.719 6.844,3.875 0.385,0.156 10 false 100.0 4.865,3.719 4.958,3.875 0.094,0.156 10 false 0 4.396,3.615 4.49,3.771 0.094,0.156 10 false 0 4.479,4.01 7.01,4.333 2.531,0.323 10 false Exhaust Gas Differential Pressure (kPa) 4.552,1.865 6.156,2.063 1.604,0.198 10 false P1425 or P1428 detected 5.635,2.667 6.656,3.031 1.021,0.365 10 false P1425 or P1427 detected

The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF* catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration. The sensor is a semiconductor-type that is not influenced by exhaust gases.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference between the pressure before and after the catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter has clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform DPF catalyst regeneration.

When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and DTC P1425, P1427, or P1428 will be stored and the MIL will be illuminated.

*: Diesel Particulate Filter.

HINT:

If the vacuum hoses of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as abnormal pressure difference, and DTC P1426 (Differential Pressure Sensor [Installation]) will be stored and the MIL will be illuminated.


DTC No. DTC Detection Condition Trouble Area
P1425 Differential pressure sensor output voltage is less than 0.4 V, or more than 4.8 V for 1 second or more
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly

·

ECM


P1427 Differential pressure sensor output voltage is less than 0.4 V for 1 second or more
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly

·

ECM


P1428 Differential pressure sensor output voltage is more than 4.8 V for 1 second or more
(1 trip detection logic)
·

Open or short in differential pressure sensor assembly circuit

·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly

·

ECM



HINT:

After confirming DTC P1425, P1427 and P1428, check the differential pressure by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Result
Condition Differential Pressure Output Sensor Condition
Ignition Switch ON Approximately 0 kPa Normal
Always -5 or 100 kPa Open or short circuit
3000 rpm (No engine load) Negative output Incorrect arrangement of hose piping


WIRING DIAGRAM

A198999E26
5.188,1.948 5.448,2.115 0.26,0.167 10 false 28 5.146,2.135 5.448,2.344 0.302,0.208 10 false B59 5.188,1.427 5.427,1.604 0.24,0.177 10 false 27 5.146,1.625 5.448,1.823 0.302,0.198 10 false B60 5.188,0.896 5.427,1.083 0.24,0.188 10 false 18 1.583,2.146 1.813,2.354 0.229,0.208 10 false E2 1.469,1.615 1.823,1.802 0.354,0.188 10 false PEX 1.583,1.104 1.833,1.302 0.25,0.198 10 false VC 5.49,2.135 5.833,2.344 0.344,0.208 10 false E2 5.49,1.615 5.823,1.813 0.333,0.198 10 false PEX 5.49,1.104 5.833,1.292 0.344,0.188 10 false VC 5.146,1.094 5.469,1.292 0.323,0.198 10 false B59 5.865,2.917 6.26,3.104 0.396,0.188 10 false ECM 0.521,2.573 0.833,2.75 0.313,0.177 10 false A43 0.51,2.74 3.031,2.938 2.521,0.198 10 false Differential Pressure Sensor Assembly 1.875,2.021 2,2.208 0.125,0.188 10 false 1 1.885,1.5 2.01,1.698 0.125,0.198 10 false 2 1.885,0.99 2.021,1.177 0.135,0.188 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (DIFFERENTIAL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.


e.

Check that differential pressure is within the specification below.


Result:
Condition Differential Pressure Proceed to
Always -5 kPa or less A
-1 to 1 kPa B
100 kPa C



A

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - CATALYTIC CONVERTER)

B

C

3.CHECK BLOCKAGE OF VACUUM HOSE AND CATALYTIC CONVERTER
2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - CATALYTIC CONVERTER)
a.

Check if the vacuum hose routing between the differential pressure sensor assembly and the catalytic converter is correct.


b.

Check that there is no exhaust gas leak between the differential pressure sensor assembly and the catalytic converter.


Result:
Proceed to
OK
NG



OK

3.CHECK BLOCKAGE OF VACUUM HOSE AND CATALYTIC CONVERTER

NG

RECONNECT TO VACUUM HOSE

3.CHECK BLOCKAGE OF VACUUM HOSE AND CATALYTIC CONVERTER
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.

Disconnect the vacuum hose (both upstream and downstream) on the differential pressure sensor assembly.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both vacuum hoses during idling.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)

NG

REPLACE CLOGGED PARTS

4.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR ASSEMBLY - ECM)
a.

Disconnect the differential pressure sensor assembly connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B60-27 (PEX) - A43-2 (PEX) Always Below 1 Ω
B59-18 (VC) - A43-3 (VC) Always Below 1 Ω
B59-28 (E2) - A43-1 (E2) Always Below 1 Ω
B60-27 (PEX) or A43-2 (PEX) - Body ground Always 10 kΩ or higher
B59-18 (VC) or A43-3 (VC) - Body ground Always 10 kΩ or higher



d.

Reconnect the differential pressure sensor assembly connector.


e.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR