Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0095  Intake Air Temperature Sensor 2 Circuit  P0097  Intake Air Temperature Sensor 2 Circuit Low  P0098  Intake Air Temperature Sensor 2 Circuit High  


DESCRIPTION

A208462E47
1.469,2 1.625,1.76 1.625,1.76 1.771,1.76 false 0.208,0.146 0.906,0.49 0.698,0.344 10 false (Fig. 1) 0.208,0.542 1.313,0.823 1.104,0.281 10 false Resistance kΩ 1.823,1.688 2.656,2.031 0.833,0.344 10 false Acceptable 1.208,4.073 2.521,4.385 1.313,0.313 10 false Temperature °C (°F)

The intake air temperature sensor (after turbocharged), mounted on the intake manifold, senses the turbocharged air temperature. A thermistor built in the sensor changes the resistance value according to the intake air temperature. The lower the intake air temperature is the greater the thermistor resistance value becomes, and the higher the intake air temperature is the lower the thermistor resistance value becomes (see Fig. 1).

The intake air temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THIA via a resistor R. The resistor R and intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the voltage at terminal THIA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.

DTC No. DTC Detection Condition Trouble Area
P0095 Open or short in intake air temperature sensor (after turbocharged) circuit for 0.5 seconds (1 trip detection logic)
·

Open or short in intake air temperature sensor (after turbocharged) circuit

·

Intake air temperature sensor (after turbocharged)

·

ECM


P0097 Short in intake air temperature sensor (after turbocharged) circuit for 0.5 seconds
·

Short in intake air temperature sensor (after turbocharged) circuit

·

Intake air temperature sensor (after turbocharged)

·

ECM


P0098 Open in intake air temperature sensor (after turbocharged) circuit for 0.5 seconds
·

Open in intake air temperature sensor (after turbocharged) circuit

·

Intake air temperature sensor (after turbocharged)

·

ECM



HINT:

When any of DTCs are stored, check the intake air temperature by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
190°C (374°F) or more Short circuit


WIRING DIAGRAM

A398533E01
0.281,2.75 2.208,3.115 1.927,0.365 10 false Intake Air Temperature Sensor 0.271,2.552 0.729,2.75 0.458,0.198 10 false B13 4.979,1.323 5.438,1.521 0.458,0.198 10 false B105 4.99,1.896 5.448,2.094 0.458,0.198 10 false B104 1.542,1.219 2,1.417 0.458,0.198 10 false THA 1.646,1.76 2.104,1.958 0.458,0.198 10 false E2 5.458,1.208 5.917,1.406 0.458,0.198 10 false THIA 5.479,1.781 5.938,1.979 0.458,0.198 10 false E2 5.073,1.677 5.531,1.875 0.458,0.198 10 false 14 5.115,1.104 5.323,1.302 0.208,0.198 10 false 8 2,1.125 2.208,1.323 0.208,0.198 10 false 2 2,1.729 2.208,1.927 0.208,0.198 10 false 1 6.198,0.844 6.656,1.042 0.458,0.198 10 false 5 V 6.094,1.115 6.552,1.313 0.458,0.198 10 false R 5.875,2.823 6.333,3.021 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


e.

Read the value.

Standard:

Same value as the actual inlet air temperature.


Result:
Result Proceed to
-40°C (-40°F) A
190°C (374°F) or more B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 190°C (374°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
A227773E05
0.344,0.948 0.833,1.302 0.49,0.354 0.719,1.781 1.552,1.25 true 2.604,1.771 2,1.26 true 0.104,0.083 0.427,0.375 0.323,0.292 10 false *a 0.469,1.042 0.771,1.219 0.302,0.177 10 false B13 0.5,1.802 0.813,2 0.313,0.198 10 false E2 2.573,1.802 2.885,2 0.313,0.198 10 false THA

a.

Disconnect the intake air temperature sensor connector.


b.

Connect terminals 1 (E2) and 2 (THA) of the intake air temperature sensor harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


g.

Read the value.

Standard:

190°C (374°F) or more


Text in Illustration
*a Front view of wire harness connector
(to Intake Air Temperature Sensor)


Result:
Proceed to
OK
NG



OK

NG

3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
3.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
A260250E31
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 2.177,0.875 2.333,1.74 true 1.688,0.802 1,1.74 true 1.396,0.167 1.813,0.323 0.417,0.156 10 false B105 1.938,0.167 2.417,0.323 0.479,0.156 10 false B104 0.063,0.073 0.25,0.281 0.188,0.208 10 false *a 2.146,1.771 2.844,2.01 0.698,0.24 10 false 14 (E2) 0.771,1.771 1.406,2.042 0.635,0.271 10 false 8 (THIA)

a.

Disconnect the intake air temperature sensor connector.


b.

Connect terminals THIA and E2 of the ECM connector.

HINT:

Before checking, do a visual and contact pressure check for the ECM connector.



c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).


g.

Read the value.

Standard:

190°C (374°F) or more


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)

NG

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the intake air temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT/ Data List / Intake Air Temp (Turbo).


f.

Read the value.

Standard:

-40°C (-40°F)



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)
5.CHECK HARNESS AND CONNECTOR (ECM - INTAKE AIR TEMPERATURE SENSOR)
a.

Disconnect the intake air temperature sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according the valve(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-8 (THIA) or B13-2 (THA) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B13-1 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR