Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0219  Engine Overspeed Condition  


DESCRIPTION

This DTC is stored when the engine speed exceeds the threshold.

DTC No. DTC Detection Condition Trouble Area
P0219 The engine speed is 3740 rpm or more for 0.5 seconds or more when the vehicle is being driven at a speed of 3 km/h (1.8 mph) or more and the battery voltage is 8 V or higher.
(1 trip detection logic)
Engine oil level

CAUTION / NOTICE / HINT

HINT:
·

For manual transmissions, the engine may over rev due to the way the customer shifts gears. Therefore, be sure to ask the customer about their shifting habits and give advice if the customer has mentioned that the engine over revved.

·

The engine may suck in an excessive amount of oil and over rev due to an increase in the engine oil level. Therefore, be sure to ask the customer about their vehicle usage and give advice if the customer has mentioned that the engine over revved.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.

·
A301856E28
2.24,0.938 3.083,1.167 0.844,0.229 10 false 0.5 seconds 0.344,0.938 1.188,1.167 0.844,0.229 10 false 0.5 seconds 1.323,0.927 2.167,1.156 0.844,0.229 10 false 0.5 seconds 0.406,2.813 2.844,3.031 2.438,0.219 10 false Freeze frame data recorded point 2.344,0.198 3.323,0.406 0.979,0.208 10 false DTC is stored 0.229,2.5 0.458,2.708 0.229,0.208 10 false 1 1.177,2.521 1.406,2.729 0.229,0.208 10 false 2 2.125,2.51 2.354,2.719 0.229,0.208 10 false 3 2.729,2.698 2.958,2.906 0.229,0.208 10 false 4 3.063,2.49 3.292,2.698 0.229,0.208 10 false 5

The fourth set of freeze frame data is the data recorded when the DTC is stored.



PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Record the stored DTCs and freeze frame data.

HINT:

This freeze frame data shows the actual engine conditions when engine stall trouble occurred.



Result:
Proceed to
NEXT



NEXT

2.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0219)
2.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0219)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes. Read the DTCs.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0219 is output A
DTC is not output B



A

3.CHECK ENGINE ASSEMBLY

B

3.CHECK ENGINE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

REPAIR OR REPLACE MALFUNCTIONING PARTS