Home › Engine / Hybrid System › N04C-VQ (ENGINE MECHANICAL) › ENGINE › 2017.01–2019.08
RM2850E _51 Engine / Hybrid System _073144 N04C-VQ ENGINE MECHANICAL _0355903 ENGINE G

N04C-VQ ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT FOR ENGINE COOLANT

Hide 5.INSPECT FOR AIR CLEANER ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


b.

Visually check that there is no dirt, blockage, or damage to the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or blockages in the air cleaner filter element, clean it with compressed air.

·

If any dirt or blockages remain even after cleaning the air cleaner filter element with compressed air, replace it.




Hide 6.INSPECT FOR ENGINE IDLING SPEED AND MAXIMUM SPEED

NOTICE:

Turn all electrical systems and the A/C off.


a.

Warm up and then stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Enter the following menus: Powertrain / Engine and ECT / Data List

HINT:

Refer to the GTS operator manual for further information regarding the selection of Data List.



iv.

Inspect the engine idling speed.

Standard idling speed:

600 to 700 rpm



v.

Fully depress the accelerator pedal.


vi.

Check the maximum speed.

Maximum speed:

3600 to 3700 rpm



vii.

Turn the ignition switch off.


viii.

Disconnect the GTS from the DLC3.



c.
A206183E07
0.75,1.885 0.875,1.885 0.875,1.885 1.052,1.469 false 0.115,0.104 0.313,0.302 0.198,0.198 10 false *a 0.438,1.792 0.76,1.969 0.323,0.177 10 false TAC

When not using the GTS:

i.

Install SST to terminal (TAC) of DLC3, then connect a tachometer.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3

NOTICE:

Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



ii.

Turn the ignition switch to ON.


iii.

Inspect the engine idling speed.

Standard idle speed:

600 to 700 rpm



iv.

Fully depress the accelerator pedal.


v.

Check the maximum speed.

Maximum speed:

3600 to 3700 rpm



vi.

Turn the ignition switch off.


vii.

Disconnect the tachometer.


viii.

Remove SST from terminal.



Hide 7.INSPECT FOR COMPRESSION

a.

Warm up and stop the engine.


b.

Remove the oil filler cap sub-assembly.


c.

Remove the 2 bolts and cylinder head cover sub-assembly.


d.

Disconnect all connectors from the 4 injectors.


e.

Remove the 4 bolts from the 4 glow plug holes.


f.

Crank the engine to remove foreign matter before measuring the compression.


g.
A101588E01
1.996,0.041 2.363,0.266 0.367,0.225 10 SST 1.617,0.739 1.757,0.14 1.757,0.14 1.961,0.14 false

Install SST (attachment) into the glow plug hole.

SST
09992-19015  
09992-10130  


h.

Connect SST (compression gauge) to SST (attachment).


i.

While cranking the engine, measure the compression pressure.

Standard pressure:

3200 kPa (32.6 kgf/cm2 464 psi)


Minimum pressure:

2700 kPa (27.5 kgf/cm2 392 psi)


Maximum difference between each cylinder:

290 kPa (3.0 kgf/cm2 42 psi)


NOTICE:
·

Use a fully-charged battery so that the engine speed can be increased to 280 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure in as short a time as possible.



If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the glow plug hole, then inspect it again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.




j.

Remove SST (compression gauge) and SST (attachment).


k.

Install the 4 bolts to the 4 glow plug holes.

Torque:

23 N*m (229 kgf*cm, 17 ft.*lbf)



l.

Connect all connectors to the 4 injectors.


m.

Install the 2 bolts and cylinder head cover sub-assembly.


n.

Install the cylinder head cover sub-assembly with the 2 bolts.

Torque:

29 N*m (291 kgf*cm, 21 ft.*lbf)



o.

Install the oil filter cap sub-assembly.


Hide 8.INSPECT FOR DIESEL SMOKE

Standard value (Black smoke):

10% or less