Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0340  Camshaft Position Sensor Circuit  


DESCRIPTION

The camshaft position sensor (G signal) consists of a magnet and MR element.

The camshaft drive gear has 5 teeth on its inner circumference. When the camshaft drive gear rotates, air gap changes between the protrusion on the gear and the pickup coil. The change affects the magnetic field and results in change in the resistance of the MR element. The crankshaft angle sensor plate has 32 teeth and output 32 signals every engine revolution. The ECM detects the standard crankshaft angle based on the G signal and actual crankshaft angle and engine speed by NE signal.

DTC No. DTC Detection Condition Trouble Area
P0340 STA ON (2 trip detection logic):
No camshaft position sensor signal to ECM while cranking for 4 seconds or more
STA OFF (1 trip detection logic):
No camshaft position sensor signal to ECM with engine speed 650 to 3000 rpm 20 times or more
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft (camshaft drive gear)

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK CAMSHAFT POSITION SENSOR
a.
A257466E15
2.281,0.344 2.75,0.604 0.469,0.26 1.26,1.688 2.583,0.969 true 1.729,1.875 2.583,1.042 true 2.417,1.917 2.635,1.042 true 2.979,1.688 2.635,0.969 true 0.156,0.073 0.469,0.271 0.313,0.198 10 false *a 2.354,0.385 2.781,0.583 0.427,0.198 10 false B103 0.406,2.063 0.719,2.26 0.313,0.198 10 false *b 0.51,2.625 0.823,2.823 0.313,0.198 10 false G 0.469,3.365 0.781,3.563 0.313,0.198 10 false NE 1.292,4.083 2.333,4.302 1.042,0.219 10 false 20 ms./DIV. 2.896,2.802 3.323,3.01 0.427,0.208 10 false GND 2.906,3.385 3.333,3.594 0.427,0.208 10 false GND 2.708,2.292 3.427,2.573 0.719,0.281 10 false 5 V/DIV. 0.781,1.646 1.313,1.833 0.531,0.188 10 false 8 (NE-) 1.448,1.906 1.979,2.094 0.531,0.188 10 false 14 (G-) 2.135,1.948 2.729,2.135 0.594,0.188 10 false 13 (G+) 2.708,1.719 3.302,1.906 0.594,0.188 10 false 7 (NE+)

While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

Standard:
Tester Connection Condition Specified Condition
B103-7 (NE+) - B103-8 (NE-) Idling Correct waveform appears as shown
B103-13 (G+) - B103-14 (G-) Idling Correct waveform appears as shown


Text in Illustration
*a Component with harness connected
(ECM)
*b G and NE Signal Waveform


Result:
Proceed to
OK
NG



OK

NG

2.CHECK ECM (VCG VOLTAGE)
2.CHECK ECM (VCG VOLTAGE)
a.
A258701E10
2.323,0.219 2.771,0.458 0.448,0.24 2.927,1.552 2.583,0.885 true 1.896,1.563 2.469,0.875 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 2.385,0.25 2.813,0.448 0.427,0.198 10 false B103 2.708,1.594 3.24,1.792 0.531,0.198 10 false 14(G-) 1.583,1.594 2.25,1.792 0.667,0.198 10 false 15(VCG)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B103-15 (VCG) - B103-14 (G-) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k2-1 (G1) - B103-13 (G+) Always Below 1 Ω
k2-2 (G-) - B103-14 (G-) Always Below 1 Ω
k2-3 (VG) - B103-15 (VCG) Always Below 1 Ω
k2-1 (G1) or B103-13 (G+) - Body ground Always 10 kΩ or higher
k2-2 (G-) or B103-14 (G-) - Body ground Always 10 kΩ or higher
k2-3 (VG) or B103-15 (VCG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

4.CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION)
a.

Check the camshaft position sensor installation condition.


A430055E01
0.406,0.031 0.719,0.229 0.313,0.198 10 false *a 2.51,0.031 2.823,0.229 0.313,0.198 10 false *b 2.656,1.813 2.969,2.01 0.313,0.198 10 false *c

OK:

The camshaft position sensor is installed properly.


Text in Illustration
*a OK
*b NG
*c Clearance

Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT (CAMSHAFT DRIVE GEAR)

NG

5.INSPECT CAMSHAFT (CAMSHAFT DRIVE GEAR)
a.

Check the teeth of the camshaft drive gear.


Result:
Proceed to
OK
NG



OK

6.REPLACE CAMSHAFT POSITION SENSOR

NG

REPLACE CAMSHAFT (CAMSHAFT DRIVE GEAR)

6.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0340 is output A
DTC is not output B



A

B

END