Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0704  Clutch Switch Input Circuit  


DESCRIPTION

The exhaust retarder switch assembly is mounted on the clutch pedal. The switch is turned off when depressing the clutch pedal, and transmits a signal to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0704 No clutch switch signals to ECM despite vehicle driving with varying vehicle speed between 0 and 80 km/h.
(1 trip detection logic)
·

Open or short in exhaust retarder switch circuit

·

Exhaust retarder switch assembly

·

Ignition switch assembly

·

ECM



WIRING DIAGRAM

A431932E02
0.302,1.063 1.802,1.583 1.5,0.521 10 false From Instrument Panel Junction Block Terminal (4A-35) 5.323,1.24 5.938,1.438 0.615,0.198 10 false CLSW 5.646,2.229 6.26,2.427 0.615,0.198 10 false A57 5.635,2.396 6.25,2.594 0.615,0.198 10 false ECM 5.052,1.125 5.667,1.323 0.615,0.198 10 false 21 4.531,1.115 5.146,1.313 0.615,0.198 10 false 2 2.948,1.125 3.563,1.323 0.615,0.198 10 false 1 2.854,1.542 3.469,1.74 0.615,0.198 10 false H3 2.844,1.677 5.125,1.875 2.281,0.198 10 false Exhaust Retarder Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.INSPECT EXHAUST RETARDER SWITCH ASSEMBLY
a.

Inspect the exhaust brake clutch switch (exhaust retarder switch assembly).


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST RETARDER SWITCH ASSEMBLY)

NG

REPLACE EXHAUST RETARDER SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST RETARDER SWITCH ASSEMBLY)
a.

Disconnect the exhaust retarder switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-2 - A57-21 (CLSW) Always Below 1 Ω
H3-2 or A57-21 (CLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST RETARDER SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST RETARDER SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (EXHAUST RETARDER SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the exhaust retarder switch assembly connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 - 4A-35 Always Below 1 Ω
H3-1 or 4A-35 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR (EXHAUST RETARDER SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)