Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0850  Park / Neutral Switch Input Circuit  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
P0850 No exhaust brake neutral switch signals to ECM despite vehicle driving with varying vehicle speed between 0 and 80 km/h:
(1 trip detection logic)
·

Open or short in exhaust brake neutral switch circuit

·

Exhaust brake neutral switch assembly

·

ECM



WIRING DIAGRAM

A398547E01
5.24,0.781 5.552,0.979 0.313,0.198 10 false 21 3.958,0.792 4.271,0.99 0.313,0.198 10 false 1 2.573,0.802 2.885,1 0.313,0.198 10 false 2 2.76,0.896 3.375,1.094 0.615,0.198 10 false NSW- 3.458,0.896 4.073,1.094 0.615,0.198 10 false NSW+ 2.406,1.219 2.865,1.417 0.458,0.198 10 false B25 2.406,1.417 3.875,1.823 1.469,0.406 10 false Exhaust Brake Neutral Switch Assembly 5.479,0.896 6.094,1.094 0.615,0.198 10 false NUSW 5.75,1.917 6.365,2.115 0.615,0.198 10 false B103 5.75,2.115 6.365,2.313 0.615,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.INSPECT EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY
a.

Inspect the exhaust brake neutral switch assembly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - ECM)

NG

REPLACE EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - ECM)
a.

Disconnect the exhaust brake neutral switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-1 (NSW+) - B103-21 (NUSW) Always Below 1 Ω
B25-1 (NSW+) or B103-21 (NUSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - ECM)

3.CHECK HARNESS AND CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the exhaust brake neutral switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-2 (NSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - BODY GROUND)