Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P1603  Engine Stall History  


DESCRIPTION

After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.

Using the GTS, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.

DTC No. DTC Detection Condition Trouble Area
P1603 2 seconds or more elapse after starting the engine, and the engine running, the engine stops for 0.5 seconds or more without the ignition switch being operated
(Fuel pressure drops to 10000 kPa or less and fuel injection is stopped)
(1 trip detection logic)
·

Injector assembly

·

Injector compensation code

·

Fuel leak

·

Injection or supply pump assembly

(suction control valve)

·

Low quality fuel

·

Diesel fuel filter assembly air bleed problem

·

Diesel fuel filter assembly clog



Related Data List
DTC No. Data List
P1603
·

Engine Speed

·

Battery Voltage

·

Engine Speed of Cyl #1 (to #4)

·

Target Common Rail Pressure

·

Fuel Press

·

Common Rail Pres Sens 2

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume



CAUTION / NOTICE / HINT

Fuel system


a.

The following malfunctions may be present in the fuel system.

i.

Problem with injector assemblies.


ii.

Problem with injection or supply pump assembly.


iii.

Air in fuel pipe.


iv.

Diesel fuel filter assembly clog.




Engine assembly


a.

The following malfunctions may be present in the engine assembly.

i.

Insufficient compression.




HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1603 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.As the DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.

·
A301856E28
2.24,0.938 3.083,1.167 0.844,0.229 10 false 0.5 seconds 0.344,0.938 1.188,1.167 0.844,0.229 10 false 0.5 seconds 1.323,0.927 2.167,1.156 0.844,0.229 10 false 0.5 seconds 0.406,2.813 2.844,3.031 2.438,0.219 10 false Freeze frame data recorded point 2.344,0.198 3.323,0.406 0.979,0.208 10 false DTC is stored 0.229,2.5 0.458,2.708 0.229,0.208 10 false 1 1.177,2.521 1.406,2.729 0.229,0.208 10 false 2 2.125,2.51 2.354,2.719 0.229,0.208 10 false 3 2.729,2.698 2.958,2.906 0.229,0.208 10 false 4 3.063,2.49 3.292,2.698 0.229,0.208 10 false 5

The fourth set of freeze frame data is the data recorded when the DTC is stored.



PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Record the stored DTC and freeze frame data.

HINT:

This freeze frame data shows the actual engine conditions when engine stall trouble occurred.



Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
P1603 is output A
P1603 and other DTCs are output B


HINT:

If any DTCs other than DTC P1603 are output, troubleshoot those DTCs first.




A

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT)

B

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT)
a.

Determine the cause of the problem based on the freeze frame data recorded in Procedure 1.

Battery Voltage
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Battery Voltage" in freeze frame data is below 6 V Engine starting trouble may have occurred because battery is fully depleted During cranking: 6 V or higher The battery may be fully depleted or the battery terminals may be loose.

Fuel Press
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Fuel Press" in freeze frame data is below 25000 kPa (254.9 kgf/cm2, 3626 psi) Problem supplying fuel to fuel supply pump assembly (low pressure side)
·

Ran out of fuel, air in fuel, fuel frozen (in this case, values of "Fuel Temperature" and "Coolant Temp" in freeze frame data are low)

·

Diesel fuel filter assembly clog, fuel line clog (low pressure side) or fuel leak

·

Feed pump (in fuel supply pump assembly) malfunctioning


Problem supplying fuel to fuel supply pump assembly (low pressure side) or problem on high pressure side
·

Fuel supply pump assembly (suction control valve operation malfunction)

·

Common rail assembly


When in a stable condition such as when the engine is idling after being warmed up, the fuel pressure is within +/-5000 kPa of the target fuel pressure
HINT:

In order to maintain the injection amount before an engine stall, the target common rail pressure is increased drastically. At this time, Common Rail Pressure may not follow correctly, but this is normal behavior and not a malfunction.


If "Fuel Press" is 10000 kPa (102.0 kgf/cm2, 1451 psi) or less, fuel injection control is stopped.
HINT:

Refer to Engine Difficult to Start or Stalling for the inspection procedure (Click here(Click here)).



Injection Feedback Val #1(to #4)
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Injection Feedback Val #1 (to #4)" in freeze frame data is not +2.0 mm3/st or less Injector assembly malfunction or compression problem -2.0 to +2.0 mm3/st If an injector assembly is malfunctioning, even though the engine starts, idling is rough.
HINT:

Refer to Engine Difficult to Start or Stalling for the inspection procedure (Click here (Click here)).


"Injection Feedback Val #1 (to #4)" in Data List is not +2.0 mm3/st or less when idling

Injection Volume
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Injection Volume" in Data List is 10 mm3/st or less and "Injection Feedback Val #1 (to #4)" is within range of 2.0 mm3/st when idling after warming up engine Injector assemblies of all cylinders malfunctioning -
HINT:

Refer to Engine Difficult to Start or Stalling for the inspection procedure (Click here (Click here)).




Result:
Proceed to
NEXT



NEXT