Refer to DTC P0087 for fuel pressure sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0087).
Refer to DTC P0115 for engine coolant temperature sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0115).
Refer to DTC P0201 for injector circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0201).
Refer to DTC P0335 for crankshaft position sensor circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0335).
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.
If the vehicle runs out of fuel while the engine is operating, there is a chance that the engine may be difficult to restart after fuel is refilled.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTCs related to engine | B |
A
B
Check that the fuel filter is not clogged.
Fuel filter is not clogged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the engine cranking condition.
Compare the cranking condition with that of a normal engine of the same model, and carefully check if there is any difference between them.
Engine cranking condition is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Read the value.
| GTS Display | Condition | Reference Value |
|---|---|---|
| Fuel Press | Cranking, and engine coolant temperature 0°C (32°F) or more | 15000 kPa or more |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if initial combustion occurs.
| Result | Proceed to |
|---|---|
| Initial combustion occurs | OK |
| No initial combustion | NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Check that the internal fuel pressure of the common rail assembly is within the specification below.
| GTS Display | Condition | Reference Value |
|---|---|---|
| Fuel Press | Idling | Approximately 20000 to 30000 kPa |
| 3000 rpm (No engine load) | Approximately 130000 to 150000 kPa |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the engine condition (Click hereEngine / Hybrid System>N04C-VQ (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the exhaust retarder assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Enter the following menus in order and read the values.
Fuel Press
Injection Volume
| GTS Display | Condition* | Reference Value |
|---|---|---|
| Fuel Press | Idling | 20000 to 30000 kPa |
| Injection Volume | Idling | 5.0 to 16.0 mm3/st |
*: If no idling conditions are specified, the shift lever should be in neutral, and the A/C switch and all accessory switches should be off.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-VQ (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the wire harness between the injector assembly and injector driver assembly (IJ terminal).
Disconnect the injector assembly connectors.
Disconnect the injector driver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i1-2 - B98-1 (IJ1+) | Always | Below 1 Ω |
| i2-2 - B98-6 (IJ2+) | Always | Below 1 Ω |
| i3-2 - B98-5 (IJ3+) | Always | Below 1 Ω |
| i4-2 - B95-3 (IJ4+) | Always | Below 1 Ω |
| i1-1 - B95-6 (IJ1-) | Always | Below 1 Ω |
| i2-1 - B95-4 (IJ2-) | Always | Below 1 Ω |
| i3-1 - B95-2 (IJ3-) | Always | Below 1 Ω |
| i4-1 - B95-5 (IJ4-) | Always | Below 1 Ω |
| i1-2 or B98-1 (IJ1+) - Body ground | Always | 10 kΩ or higher |
| i2-2 or B98-6 (IJ2+) - Body ground | Always | 10 kΩ or higher |
| i3-2 or B98-5 (IJ3+) - Body ground | Always | 10 kΩ or higher |
| i4-2 or B95-3 (IJ4+) - Body ground | Always | 10 kΩ or higher |
| i1-1 or B95-6 (IJ1-) - Body ground | Always | 10 kΩ or higher |
| i2-1 or B95-4 (IJ2-) - Body ground | Always | 10 kΩ or higher |
| i3-1 or B95-2 (IJ3-) - Body ground | Always | 10 kΩ or higher |
| i4-1 or B95-5 (IJ4-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3 and #4 Fuel Cut.
Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.
| Result | Proceed to |
|---|---|
| Engine Idling becomes unstable | A |
| Engine Idling does not change | B |
If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.
If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.
A
B
Disconnect the inlet pipe from the injection or supply pump assembly.
Operate the priming pump and check that fuel is being supplied to the injection or supply pump assembly.
Fuel is properly supplied to the injection or supply pump assembly when the priming pump is operated.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
Measure the voltage of the ECM connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-9 (THW) - B104-14 (E2) | Idling, engine coolant temperature between 60 and 120°C (140 and 248°F) | 0.2 to 1.0 V |
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
While idling the engine, check the waveform between the specified terminals of the ECM connector using an oscilloscope.
| Tester Connection | Specified Condition |
|---|---|
| B103-7 (NE+) - B103-8 (NE-) | Correct waveform appears as shown |
| Tool Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the engine speed.
| *a | Component with harness connected
(ECM) |
| *b | G and NE Signal Waveform |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the STARTER relay from the No. 2 relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Ignition Switch Position | Specified Condition |
|---|---|---|
| ST relay terminal 1 - A57-6 (STA) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Start the engine.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-16 (PCR1) - B104-14 (E2) | Idling | 1.7 to 2.2 V |
| B105-2 (PCR2) - B105-14 (E21) | Idling | 1.2 to 1.6 V |
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel pressure sensor (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>COMMON RAIL>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
Disconnect the fuel pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B105-16 (PCR1) - m1-2 (PCR1) | Always | Below 1 Ω |
| B104-13 (VC) - m1-1 (VC1) | Always | Below 1 Ω |
| B104-14 (E2) - m1-3 (E1) | Always | Below 1 Ω |
| B105-2 (PCR2) - m1-5 (PCR2) | Always | Below 1 Ω |
| B105-13 (VC2) - m1-6 (VC2) | Always | Below 1 Ω |
| B105-14 (E21) - m1-4 (E2) | Always | Below 1 Ω |
| B105-16 (PCR1) or m1-2 (PCR1) - Body ground | Always | 10 kΩ or higher |
| B104-13 (VC) or m1-1 (VC1) - Body ground | Always | 10 kΩ or higher |
| B105-2 (PCR2) or m1-5 (PCR2) - Body ground | Always | 10 kΩ or higher |
| B105-13 (VC2) or m1-6 (VC2) - Body ground | Always | 10 kΩ or higher |
| B104-14 (E2) or m1-3 (E1) - Other terminals | Always | 10 kΩ or higher |
| B105-14 (E21) or m1-4 (E2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECM>REMOVAL).
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Check if the engine starts smoothly or if the engine stalls.
The engine starts smoothly and does not stall.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the crankshaft position sensor (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSPECTION).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the engine coolant temperature sensor.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 2.32 to 2.59 kΩ |
| 1 - 2 | 80°C (176°F) | 0.31 to 0.326 kΩ |
| *1 | Ohmmeter |
| *2 | Engine Coolant Temperature Sensor |
| *a | Acceptable |
When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.
Alternative procedure: Connect an ohmmeter to the installed engine coolant temperature sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG