Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM J

N04C-VQ ENGINE CONTROL  ECD SYSTEM  EDU Power Source Circuit  


DESCRIPTION

An injector driver assembly has been adopted to drive the injector assemblies at high speeds. The injector driver assembly has realized high-speed driving under high fuel pressure conditions through the use of a DC/DC converter sub-assembly that provides a high-voltage, quick-charging system. The ECM constantly monitors the injector driver assembly and stops the engine or cuts off fuel supply to some cylinders if an abnormal condition is detected.

WIRING DIAGRAM

A402322E03
0.802,0.927 1.063,1.104 0.26,0.177 10 false +B 0.708,1.927 1.063,2.125 0.354,0.198 10 false GND 0.25,2.406 0.604,2.604 0.354,0.198 10 false B98 0.24,2.573 1.094,2.938 0.854,0.365 10 false Injector Driver Assembly 1.125,0.823 1.344,1.01 0.219,0.188 10 false 2 1.135,1.813 1.354,2 0.219,0.188 10 false 3 2.656,2.583 3.01,2.781 0.354,0.198 10 false EDU 3.76,2.344 4.115,2.542 0.354,0.198 10 false EDU 3.76,4.208 4.115,4.406 0.354,0.198 10 false EFI 2.802,3.667 3.448,3.844 0.646,0.177 10 false EFI-MAIN 0.469,3.677 1.26,3.865 0.792,0.188 10 false R/B NO. 2-B 1.469,3.667 1.75,3.844 0.281,0.177 10 false P/I 1.083,4.844 1.583,5.052 0.5,0.208 10 false Battery 2.969,4.521 4.521,4.74 1.552,0.219 10 false No. 2 Integration Relay 6.448,5.146 6.802,5.344 0.354,0.198 10 false ECM 6.167,4.698 6.417,4.885 0.25,0.188 10 false E1 5.698,4.698 6.073,4.906 0.375,0.208 10 false B102 0.427,4.031 1.083,4.219 0.656,0.188 10 false FL MAIN 5.74,3.979 6.042,4.177 0.302,0.198 10 false A56 6.156,3.979 6.594,4.167 0.438,0.188 10 false MREL 6.177,2.094 6.615,2.281 0.438,0.188 10 false IREL 5.708,2.094 6.073,2.281 0.365,0.188 10 false B104 2.125,3.521 2.375,3.719 0.25,0.198 10 false 2E 2.135,3.979 2.385,4.177 0.25,0.198 10 false 2D 2.156,3.323 2.323,3.5 0.167,0.177 10 false 1 2.167,3.781 2.333,3.958 0.167,0.177 10 false 3 4.656,1.635 4.906,1.833 0.25,0.198 10 false 2C 4.667,2.094 4.917,2.292 0.25,0.198 10 false 2C 4.656,2.792 4.906,2.99 0.25,0.198 10 false 2C 4.656,3.521 4.906,3.719 0.25,0.198 10 false 2D 4.656,3.979 4.906,4.177 0.25,0.198 10 false 2D 4.698,3.313 4.844,3.5 0.146,0.188 10 false 4 4.698,3.802 4.865,3.979 0.167,0.177 10 false 2 4.698,2.604 4.865,2.781 0.167,0.177 10 false 2 4.708,1.906 4.875,2.083 0.167,0.177 10 false 3 4.698,1.427 4.844,1.615 0.146,0.188 10 false 4 5.365,3.219 6.229,3.563 0.865,0.344 10 false EFI NO. 2 5.823,4.5 5.979,4.698 0.156,0.198 10 false 1 5.802,3.771 6,3.958 0.198,0.188 10 false 25 5.781,1.885 5.979,2.073 0.198,0.188 10 false 20

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK INJECTOR DRIVER ASSEMBLY (POWER SOURCE)
a.
A256735E07
1.49,0.292 1.917,0.531 0.427,0.24 0.917,0.729 1.677,1.042 true 1.938,1.063 2.427,0.885 true 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 1.563,0.323 1.875,0.521 0.313,0.198 10 false B98 0.677,0.625 0.99,0.823 0.313,0.198 10 false +B 2.521,0.781 2.917,0.979 0.396,0.198 10 false GND

Disconnect the injector driver assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B98-2 (+B) - B98-3 (GND) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Injector Driver Assembly)


d.

Reconnect the injector driver assembly connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT INTEGRATION NO.2 RELAY (EDU RELAY)

NG

INSPECT INTEGRATION NO.2 RELAY (EDU RELAY)

2.INSPECT INTEGRATION NO.2 RELAY (EDU RELAY)
a.

Inspect the No. 2 integration relay (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - INJECTOR DRIVER ASSEMBLY, BODY GROUND)

NG

GO TO RELAY (NO. 2 INTEGRATION RELAY)

3.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - INJECTOR DRIVER ASSEMBLY, BODY GROUND)
a.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the injector driver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
2C-4 - B98-2 (+B) Always Below 1 Ω
B98-3 (GND) - Body ground Always Below 1 Ω
2C-4 or B98-2 (+B ) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

4.CHECK INTEGRATION NO.2 RELAY (NO. 2 INTEGRATION RELAY - BATTELY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INTEGRATION NO.2 RELAY (NO. 2 INTEGRATION RELAY - BATTELY)
a.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-2 - 2D-4 Always Below 1 Ω
2E-1 - Battery Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - ECM,BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - ECM,BODY GROUND)
a.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-3 - B104-20 (IREL) Always Below 1 Ω
B102-1 (E1) - Body ground Always Below 1 Ω
2C-3 or B104-20 (IREL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR