Home › Drivetrain › A444E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY › 2017.01–2021.01
RM2850E _52 Drivetrain _073139 A444E AUTOMATIC TRANSMISSION / TRANSAXLE _0355873 AUTOMATIC TRANSMISSION ASSEMBLY A

A444E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE NO.1 ENGINE UNDER COVER

Hide 37110B 4.REMOVE PROPELLER SHAFT GUARD

Hide 37100 5.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 17430 6.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 17420 7.REMOVE CENTER NO. 2 EXHAUST PIPE ASSEMBLY

Hide 89425 8.REMOVE EXHAUST GAS TEMPERATURE SENSOR

Hide 89425A 9.REMOVE NO.2 EXHAUST GAS TEMPERATURE SENSOR

Hide 10.REMOVE EXHAUST PIPE AIR HOSE

Hide 17460 11.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 44773D 12.DISCONNECT SOLENOIDO TO RETARDER HOSE

Hide 17402 13.REMOVE FRONT NO.2 EXHAUST PIPE SUB-ASSEMBLY

Hide 17410 14.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 46501 15.REMOVE PARKING BRAKE DRUM SUB-ASSEMBLY

a.

Remove the parking brake drum sub-assembly.

SST
09930-00010  


Hide 16.REMOVE PARKING BRAKE ASSEMBLY

a.
C174333

Remove the 4 bolts and parking brake assembly.

HINT:

Hang the parking brake assembly on the vehicle with a piece of rope.



Hide 17.SEPARATE HEIGHT CONTROL COMPRESSOR

Hide 87260 18.SEPARATE HEATER PUMP ASSEMBLY

Hide 32921 19.SEPARATE NO.1 OIL COOLER INLET TUBE

a.

Remove the 5 bolts and 5 brackets.

C102097


b.
C102098

Disconnect the No.1 oil cooler inlet tube from the automatic transmission assembly.


Hide 32922 20.SEPARATE NO.1 OIL COOLER OUTLET TUBE

a.
C102099

Disconnect the No.1 oil cooler outlet tube from the automatic transmission assembly.


Hide 33820B 21.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 33823 22.REMOVE NO.1 TRANSMISSION CONTROL CABLE BRACKET

a.
C103014

Remove the 2 bolts and No.1 transmission control cable bracket from the automatic transmission assembly.


Hide 35013 23.REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

a.
C178719E02
2.302,3.698 2.76,4.073 false 2.333,4.063 3.385,4.354 1.052,0.292 10 false Breather Hose

Remove the oil level gauge from the transmission oil filler tube sub-assembly.


b.

Disconnect the breather hose from the transmission oil filler tube sub-assembly.


c.

Remove the 2 bolts and transmission oil filler tube sub-assembly.


d.

Remove the O-ring from the transmission oil filler tube sub-assembly.


Hide 24.REMOVE CONNECTORS

a.
C103015

Disconnect the ATF temperature sensor connector.


b.
C103016

Disconnect the speedometer sensor connector.


c.
C103017

Disconnect the park/neutral position switch assembly connector and transmission wire connector.


Hide 11354 25.REMOVE FLYWHEEL HOUSING DUST SEAL

a.
C103018

Remove the flywheel housing dust seal from the automatic transmission assembly.


Hide 32101A 26.REMOVE DRIVE PLATE & TORQUE CONVERTER CLUTCH SETTING BOLT

a.
C103019

Turn the crankshaft to gain access to each bolt.


b.

Hold the crankshaft pulley nut with a wrench and remove the 6 torque converter clutch setting bolts.


Hide 27.SUPPORT ENGINE

a.

Support the engine assembly with a engine jack.


Hide 28.SUPPORT AUTOMATIC TRANSMISSION

a.
C102104

Support the automatic transmission assembly with a transmission jack.


Hide 51204 29.SEPARATE NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C372967

Remove the 12 bolts and separate the No.3 frame crossmember sub-asssembly.


b.
C103020

Remove the 4 nuts and 4 washers, separate the No.3 frame crossmember sub-asssembly from the No.1 engine mounting bracket and No.3 engine mounting bracket.


Hide 12321 30.SEPARATE NO.1 ENGINE MOUNTING BRACKET

a.
C102106

Remove the 4 bolts and separate the No.1engine mounting bracket from the automatic transmission assembly.


Hide 12325 31.SEPARATE NO.3 ENGINE MOUNTING BRACKET

a.
C102107

Remove the 4 bolts and separate the No.3 engine mounting bracket from the automatic transmission assembly.


Hide 35000 32.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.
C175327E02
1.875,1.281 2.427,1.542 2.427,1.542 1.063,1.219 false 2.469,1.458 3.375,1.938 0.906,0.479 10 true Knock Pin

Remove the 12 bolts and automatic transmission assembly.

NOTICE:
·

Do not drop the torque converter.

·

Do not damage the transmission case.

·

Be careful not to damage the knock pin.




Hide 32000 33.REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

a.
C103021E02
1.76,0.156 1.052,0.115 1.052,0.115 1.76,0.344 false 0.167,0.021 1.198,0.479 1.031,0.458 10 false Match marks

Put matchmarks on the torque converter and transmission case.


b.

Remove the torque converter clutch assembly from the automatic transmission assembly.