23670
1.REMOVE INJECTOR ASSEMBLY
2.INSPECT VALVE CLEARANCE
Set the No. 1 cylinder to TDC/compression.
| *a | Timing Mark |
Make sure that there is free play in the No. 1 cylinder rocker arms and that there is no free play in the No. 4 cylinder rocker arms.
If not, turn the crankshaft 1 revolution (360°) to set the No. 1 cylinder to TDC/compression.
Inspect the valve clearance of the No. 1 cylinder intake valve and No. 3 cylinder exhaust valve.
| Item | Specified Condition |
|---|---|
| Intake | 0.3 mm (0.0118 in.) |
| Exhaust | 0.45 mm (0.0177 in.) |
| *a | No. 1 Cylinder Intake Valve |
| *b | No. 3 Cylinder Exhaust Valve |
Do not apply excessive force to the valve adjusting screw.
If the clearance is not as specified, record the measured value, and then adjust the valve clearance.
Inspect the valve clearance of the No. 1 cylinder exhaust valve and No. 2 cylinder intake valve.
| Item | Specified Condition |
|---|---|
| Intake | 0.3 mm (0.0118 in.) |
| Exhaust | 0.45 mm (0.0177 in.) |
| *a | No. 1 Cylinder Exhaust Valve |
| *b | No. 2 Cylinder Intake Valve |
Do not apply excessive force to the valve adjusting screw.
If the clearance is not as specified, record the measured value, and then adjust the valve clearance.
Turn the crankshaft 1 revolution (360°) clockwise to set the No. 4 cylinder to TDC/compression.
| *a | Timing Mark |
Make sure that there is free play in the No. 4 cylinder rocker arms and that there is no free play in the No. 1 cylinder rocker arms.
If not, turn the crankshaft 1 revolution (360°) to set the No. 4 cylinder to TDC/compression.
Inspect the valve clearance of the No. 2 cylinder exhaust valve and No. 4 cylinder intake valve.
| Item | Specified Condition |
|---|---|
| Intake | 0.3 mm (0.0118 in.) |
| Exhaust | 0.45 mm (0.0177 in.) |
| *a | No. 2 Cylinder Exhaust Valve |
| *b | No. 4 Cylinder Intake Valve |
Do not apply excessive force to the valve adjusting screw.
If the clearance is not as specified, record the measured value, and then adjust the valve clearance.
Inspect the valve clearance of the No. 3 cylinder intake valve and No. 4 cylinder exhaust valve.
| Item | Specified Condition |
|---|---|
| Intake | 0.3 mm (0.0118 in.) |
| Exhaust | 0.45 mm (0.0177 in.) |
| *a | No. 3 Cylinder Intake Valve |
| *b | No. 4 Cylinder Exhaust Valve |
Do not apply excessive force to the valve adjusting screw.
If the clearance is not as specified, record the measured value, and then adjust the valve clearance.
3.ADJUST VALVE CLEARANCE
Turn the crankshaft clockwise to align the timing mark on the crankshaft pulley with the pointer on the timing gear case.
| *a | TDC of No. 1 and No. 4 Cylinder |
| *b | TDC of No. 2 and No. 3 Cylinder |
| *c | Timing Mark |
With each piston positioned at TDC on the compression stroke, using a feeler gauge, adjust each valve clearance.
| Item | Specified Condition |
|---|---|
| Intake | 0.3 mm (0.0118 in.) |
| Exhaust | 0.45 mm (0.0177 in.) |
| *1 | Adjusting Screw |
| *2 | Lock Nut |
| *a | Feeler Gauge |
The feeler gauge should move with a very slight pull.
Loosen the lock nut on the valve rocker arm and loosen the adjusting screw.
Insert a 0.30 mm (0.0118 in.) feeler gauge for the intake valve or a 0.45 mm (0.0177 in.) feeler gauge for the exhaust valve between the adjusting screw on the valve rocker arm and the valve bridge.
Turn the adjusting screw on the valve rocker arm until the feeler gauge slides with a very slight drag, and lock the adjusting screw with the lock nut.
29 N*m (291 kgf*cm, 21 ft.*lbf)
23670
4.INSTALL INJECTOR ASSEMBLY