Home › Engine / Hybrid System › N04C-UH (ENGINE MECHANICAL) › CYLINDER HEAD
RM2850E _51 Engine / Hybrid System _073174 N04C-UH ENGINE MECHANICAL _0356076 CYLINDER HEAD A

N04C-UH ENGINE MECHANICAL  CYLINDER HEAD  REMOVAL  


PROCEDURE

Hide 16400 1.REMOVE RADIATOR ASSEMBLY

Hide 17201 2.REMOVE TURBOCHARGER SUB-ASSEMBLY

Hide 23670 3.REMOVE INJECTOR ASSEMBLY

Hide 87208L 6.REMOVE WATER PIPE SUB-ASSEMBLY

Hide 16206 7.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A345068

Disconnect the water temperature sender gauge assembly connector.


b.

Disconnect the water hose.


c.

Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly.


Hide 16206C 8.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 27020 9.REMOVE GENERATOR ASSEMBLY

Hide 16331 10.REMOVE WATER OUTLET SUB-ASSEMBLY

Hide 16331A 11.REMOVE THERMOSTAT

Hide 16333 12.REMOVE WATER OUTLET HOUSING

Hide 17111 13.REMOVE INTAKE MANIFOLD

a.
A146498

Remove the 8 bolts and 2 nuts and intake manifold.


Hide 17141 14.REMOVE EXHAUST MANIFOLD

a.
A155964

Remove the 3 bolts and exhaust manifold heat insulator.


b.
A155965

Remove the 8 nuts, 4 spacers, 4 collars and exhaust manifold.


c.

Remove the 4 exhaust manifold gaskets.


Hide 15.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.
A146510E18
2.635,1.021 1.875,0.198 false 1.719,0.052 1.917,0.323 0.198,0.271 10 false *a

Turn the crankshaft pulley until the groove of the crankshaft damper and the timing mark on the timing gear are aligned.

Text in Illustration
*a Timing Mark

HINT:
·

Make sure that there is free play in the No. 1 cylinder rocker arms and there is no free play in the No. 4 cylinder rocker arms.

·

If not, turn the crankshaft 1 revolution (360°) to set the No. 1 cylinder to TDC/compression.




Hide 13901 16.REMOVE NO. 1 VALVE ROCKER SHAFT SUB-ASSEMBLY

a.
A151464E10
1.917,1 1.563,0.292 false 1.906,1.115 1.448,1.927 false 1.344,0.177 1.521,0.354 0.177,0.177 10 false *1 1.24,1.875 1.417,2.042 0.177,0.167 10 false *2

Loosen the lock nuts at the top of the rocker arms and wind up the adjusting screws completely.

Text in Illustration
*1 Adjusting Screw
*2 Lock Nut

NOTICE:

If the adjusting screws are left unwound, the rocker shaft may bend when the rocker arm support bolts are loosened.



b.
A151465E01
0.412,0.326 0.516,0.477 0.104,0.152 10 1 1.035,0.326 1.139,0.477 0.104,0.152 10 3 1.657,0.326 1.761,0.477 0.104,0.152 10 5 2.283,0.326 2.388,0.477 0.104,0.152 10 4 2.9,0.326 3.004,0.477 0.104,0.152 10 2

Loosen the rocker arm support bolts in the order shown in the illustration.


Hide 13781 17.REMOVE VALVE PUSH ROD

a.

Remove the valve push rod.

NOTICE:

Organize the parts so that each part location can be remembered for reassembly.



Hide 13819 18.REMOVE VALVE BRIDGE

a.

Remove the valve bridge.

NOTICE:

Organize the parts so that each parts location can be remembered for reassembly.



Hide 11101 19.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A141062

Remove the 22 cylinder head set bolts in the order shown in the illustration.


b.

Lift and remove the cylinder head sub-assembly from the cylinder block.


Hide 11115 20.REMOVE CYLINDER HEAD GASKET

a.

Remove the cylinder head gasket.


Hide 13751 21.REMOVE VALVE LIFTER

a.

Remove the valve lifter.

NOTICE:

Organize the parts so that each parts location can be remembered for reassembly.