Home › Drivetrain › M15# (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for M155) › 2017.01–2021.01
RM2850E _52 Drivetrain _073186 M15# MANUAL TRANSMISSION / TRANSAXLE _0356146 MANUAL TRANSMISSION ASSEMBLY(for M155) A

M15# MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for M155)  INSTALLATION  


PROCEDURE

Hide 31111 1.INSTALL CLUTCH HOUSING

a.

Install the clutch housing to the manual transmission assembly with the 9 bolts.

Torque:

37 N*m (379 kgf*cm, 27 ft.*lbf)



Hide 31236B 2.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transmission assembly.

Torque:

47 N*m (480 kgf*cm, 35 ft.*lbf)



Hide 31126 3.INSTALL CLUTCH RELEASE FORK BOOT

a.

Install the clutch release fork boot to the manual transmission assembly.


Hide 31204 4.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C395990

Apply release hub grease to the clutch release fork sub-assembly.

Text in Illustration
V100135

Release hub grease

Grease:

Toyota Genuine Release Hub Grease or equivalent



b.

Engage the release bearing hub clip and install the clutch release fork sub-assembly to the clutch release bearing assembly.


Hide 31230 5.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.

Install the clutch release bearing assembly with the clutch release fork sub-assembly to the manual transmission assembly.


b.

Install the clutch release fork sub-assembly to the release fork support.

NOTICE:

After installation, move the fork back and forth to check that the release bearing slides smoothly.



c.
C249234

Apply clutch spline grease to the input shaft spline.

Text in Illustration
V100135

Clutch spline grease

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 12325 6.INSTALL NO. 3 ENGINE MOUNTING BRACKET

a.

Install the No. 3 engine mounting bracket to the manual transmission assembly with the 4 bolts.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 12321 7.INSTALL NO. 1 ENGINE MOUNTING BRACKET

a.

Install the No. 1 engine mounting bracket to the manual transmission assembly with the 4 bolts.

Torque:

44 N*m (449 kgf*cm, 32 ft.*lbf)



Hide 33110 8.INSTALL MANUAL TRANSMISSION ASSEMBLY (for 1HZ LHD)

a.

Support the manual transmission assembly with a transmission jack.


b.

Install the manual transmission assembly.

NOTICE:
·

Be careful not to pinch wire harnesses, etc.

·

Do not forcefully pry on the manual transmission assembly.

·

To avoid damage to the input shaft, do not forcefully shake the manual transmission assembly.

·

Insert knock pins into the knock pin holes securely so that the end face of the manual transmission assembly fits close against the engine assembly before tightening the bolts.




c.

Install the No. 1 transmission control cable bracket, 2 washers and 5 bolts.

Torque:

72 N*m (730 kgf*cm, 53 ft.*lbf)


HINT:

Install the 2 washers between the No. 1 transmission control cable bracket and the clutch housing.



Hide 33110 9.INSTALL MANUAL TRANSMISSION ASSEMBLY (for 1HZ RHD)

a.

Support the manual transmission assembly with a transmission jack.


b.

Install the manual transmission assembly.

NOTICE:
·

Be careful not to pinch wire harnesses, etc.

·

Do not forcefully pry on the manual transmission assembly.

·

To avoid damage to the input shaft, do not forcefully shake the manual transmission assembly.

·

Insert knock pins into the knock pin holes securely so that the end face of the manual transmission assembly fits close against the engine assembly before tightening the bolts.




c.

Install the 5 bolts.

Torque:

72 N*m (730 kgf*cm, 53 ft.*lbf)



Hide 33110 10.INSTALL MANUAL TRANSMISSION ASSEMBLY (for 1BZ-FPE)

a.

Support the manual transmission assembly with a transmission jack.


b.

Install the manual transmission assembly.

NOTICE:
·

Be careful not to pinch wire harnesses, etc.

·

Do not forcefully pry on the manual transmission assembly.

·

To avoid damage to the input shaft, do not forcefully shake the manual transmission assembly.

·

Insert knock pins into the knock pin holes securely so that the end face of the manual transmission assembly fits close against the engine assembly before tightening the bolts.




c.

Install the 10 bolts.

Torque:

39 N*m (400 kgf*cm, 29 ft.*lbf)



Hide 51204 11.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly to the engine mounting brackets with the 4 nuts and 4 washers.

Torque:

56 N*m (571 kgf*cm, 41 ft.*lbf)



b.

Install the No. 3 frame crossmember sub-assembly to the frame with the 12 bolts.

Torque:

50 N*m (510 kgf*cm, 37 ft.*lbf)



Hide 33119 12.INSTALL STIFFENER PLATE LH (for 1HZ)

a.

Install the stiffener plate LH to the manual transmission assembly with the 4 bolts.

Torque:

69 N*m (700 kgf*cm, 51 ft.*lbf)



Hide 33118 13.INSTALL STIFFENER PLATE RH(MTM) (for 1HZ)

a.

Install the stiffener plate RH to the manual transmission assembly with the 4 bolts.

Torque:

69 N*m (700 kgf*cm, 51 ft.*lbf)



Hide 14.CONNECT CONNECTOR

a.

Connect the connectors and wire harness clamps to the manual transmission assembly.


Hide 28100 15.INSTALL STARTER ASSEMBLY (for 1HZ)

a.

Install the starter assembly to the manual transmission assembly with the bolt, nut and washer.

Torque:

68 N*m (693 kgf*cm, 50 ft.*lbf)



b.

Connect the terminal 50 connector to the starter assembly.


c.

Connect the starter wire to the terminal 30 with the nut.

Torque:

21 N*m (215 kgf*cm, 16 ft.*lbf)



Hide 31470 16.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Install the clutch release cylinder assembly with the 2 bolts.

Torque:

12 N*m (120 kgf*cm, 9 ft.*lbf)



Hide 33820B 17.CONNECT SHIFT AND SELECT TRANSMISSION CONTROL CABLE (for 1HZ LHD)

a.

Connect the shift and select transmission control cables to the manual transmission assembly with the 2 nuts and 2 new clips.

Torque:

15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide 33709F 18.INSTALL FLOOR SHIFT CROSS SHAFT SUB-ASSEMBLY (for 1HZ RHD)

a.
C249221E03
0.198,1.365 0.375,1.563 0.177,0.198 10 true A 0.354,1.615 0.521,1.833 0.167,0.219 10 true A 2.135,1.813 2.313,2 0.177,0.188 10 true B 2.844,1.813 3.042,2.01 0.198,0.198 10 true B

Install the floor shift cross shaft sub-assembly to the manual transmission assembly with the 4 bolts.

Torque:
Bolt A:

37 N*m (377 kgf*cm, 27 ft.*lbf)

Bolt B:

18 N*m (184 kgf*cm, 13 ft.*lbf)



b.

Connect the transmission side of the shift and select transmission control links with the 2 nuts.

Torque:

15 N*m (153 kgf*cm, 11 ft.*lbf)



c.

Connect the shift lever side of the shift and select transmission control links with the 2 nuts.

Torque:

15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide 33820B 19.CONNECT SHIFT AND SELECT TRANSMISSION CONTROL CABLE (for 1BZ-FPE)

a.

Connect the shift and select transmission control cables to the manual transmission assembly with the 2 nuts and 2 new clips.

Torque:

15 N*m (153 kgf*cm, 11 ft.*lbf)



Hide 46503C 20.INSTALL PARKING BRAKE PLATE SUB-ASSEMBLY

a.

Clean the 4 bolts and their holes.


b.
A057108E72
2.188,0.229 1.948,1.094 false 2.271,0.094 2.521,0.302 0.25,0.208 12 false *1

Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

Text in Illustration
*1 Adhesive

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the parking brake plate sub-assembly to the manual transmission assembly with the 4 bolts.

Torque:

47 N*m (474 kgf*cm, 34 ft.*lbf)



Hide 46501 21.INSTALL PARKING BRAKE DRUM SUB-ASSEMBLY (for Short Wheelbase)

Hide 46501 22.INSTALL PARKING BRAKE DRUM SUB-ASSEMBLY (for Long Wheelbase)

Hide 17410 23.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1HZ)

a.

w/o Exhaust Brake:

i.

Install a new gasket.


ii.

Install the front exhaust pipe assembly to the exhaust manifold with 3 new nuts.

Torque:

62 N*m (630 kgf*cm, 46 ft.*lbf)



iii.

Install the front exhaust pipe spacer to the exhaust pipe with the 4 bolts and 2 new gaskets.

Torque:

23 N*m (235 kgf*cm, 17 ft.*lbf)




b.

w/ Exhaust Brake:

i.

Install a new gasket.


ii.

Install the front exhaust pipe assembly to the exhaust manifold with 3 new nuts.

Torque:

62 N*m (630 kgf*cm, 46 ft.*lbf)



iii.

Install the exhaust retarder assembly to the exhaust pipe with the 4 bolts and 2 new gaskets.

Torque:

23 N*m (235 kgf*cm, 17 ft.*lbf)



iv.

Connect the vacuum hose to the exhaust retarder assembly.



Hide 17410 24.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1BZ-FPE)

a.

Install a new gasket.


b.

Install the front exhaust pipe assembly to the exhaust manifold with 3 new nuts.

Torque:

62 N*m (632 kgf*cm, 46 ft.*lbf)



c.

Install the 2 bolts, 2 new nuts and a new gasket.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 17571 25.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for 1HZ)

a.

w/o Transmission Air Guide:

i.

Install the No. 1 exhaust pipe support bracket to the manual transmission assembly with the 2 bolts.

Torque:

35 N*m (360 kgf*cm, 26 ft.*lbf)



ii.

Tighten the clamp bolt.

Torque:

23 N*m (230 kgf*cm, 17 ft.*lbf)




b.

w/ Transmission Air Guide:

i.

Install the transmission air guide and the No. 1 exhaust pipe support bracket to the manual transmission assembly with the 4 bolts.

Torque:

35 N*m (360 kgf*cm, 26 ft.*lbf)



ii.

Tighten the clamp bolt.

Torque:

23 N*m (230 kgf*cm, 17 ft.*lbf)




Hide 17571 26.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET (for 1BZ-FPE)

a.

Install the No. 1 exhaust pipe support bracket to the manual transmission assembly with the 2 bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



b.

Tighten the clamp bolt.

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf)



Hide 37110F 27.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

Hide 28.ADD MANUAL TRANSMISSION OIL

a.

Park the vehicle in a level place.


b.

Remove the filler plug and gasket.


c.

Add manual transmission oil.

Oil grade:

API GL-4


Viscosity:

SAE 75W-90


Capacity (Reference):
w/o Oil Cooler:

3.2 liters (3.4 US qts, 2.8 Imp. qts)

w/ Oil Cooler:

3.8 liters (4.0 US qts, 3.3 Imp. qts)



d.
D025304E95
0.667,1.344 0.865,1.542 0.198,0.198 10 false *a

Check that the oil surface is within 5 mm (0.197 in.) below the lowest point of the filler plug opening.

Text in Illustration
*a 0 to 5 mm (0 to 0.197 in.)

NOTICE:
·

Problems may occur when the oil level is too high or too low.

·

After replacing the oil, drive the vehicle and check the oil level again.




e.

Install a new gasket and the filler plug.

Torque:

37 N*m (379 kgf*cm, 27 ft.*lbf)



Hide 29.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

3.9 N*m (40 kgf*cm, 35 in.*lbf)


Hide 30.INSPECT FOR MANUAL TRANSMISSION OIL LEAK

Hide 31.INSPECT FOR EXHAUST GAS LEAK