Wear protective gloves. Sharp areas on the parts may injure your hands.
The procedure listed below is for 2nd row to 7th row for long body, and 2nd row to 6th row for standard body.
The procedure listed below is a representative example.
Use the same procedure for all rows, unless otherwise specified.
71876E
1.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Remove the 2 screws.
for 2nd and 7th Row Seat:
Using moulding remover A, detach the 7 claws and 2 guides to remove the reclining adjuster inside cover LH.
except 2nd and 7th Row Seat:
w/ Reclining Function:
Using moulding remover A, detach the 6 claws and 2 guides to remove the reclining adjuster inside cover LH.
w/o Reclining Function:
Using moulding remover A, detach the 7 claws and 2 guides to remove the reclining adjuster inside cover LH.
71812K
2.REMOVE RECLINING ADJUSTER COVER LH
Remove the 2 screws.
for Type A:
Using moulding remover A, detach the 7 claws and 3 guides.
for Type B:
Using moulding remover A, detach the 7 claws and 2 guides.
for Type C:
Using moulding remover A, detach the 6 claws and 2 guides.
w/ Reclining Function:
Pull out the seat reclining handle belt from the hole in the reclining adjuster cover LH.
Remove the reclining adjuster cover LH.
73380A
3.REMOVE REAR SEAT INNER BELT ASSEMBLY (except 2nd Row Seat)
73306
4.REMOVE SEAT INNER BELT SUB-ASSEMBLY (for 2nd Row Seat)
Use the same procedure as for the No. 2 rear seat inner belt assembly.
72379
5.REMOVE SEAT RECLINING HANDLE BELT (w/ Reclining Function)
Remove the seat reclining handle belt from the No. 2 seatback spring assembly LH.
71148N
6.REMOVE REAR SEAT OUTER LEG COVER
Remove the 3 screws.
| *A | except 3rd Row Seat | *B | for 3rd Row Seat |
except 3rd Row Seat:
Using a clip remover with its tip wrapped with protective tape, detach the 4 clips.
|
Protective Tape | - | - |
Using moulding remover A, detach the 9 claws and 2 guides and remove the rear seat outer leg cover.
for 3rd Row Seat:
Using a clip remover with its tip wrapped with protective tape, detach the 2 clips.
|
Protective Tape | - | - |
Using moulding remover A, detach the 10 claws and guide and remove the rear seat outer leg cover.
71149K
7.REMOVE REAR SEAT INNER LEG COVER
Remove the screw.
| *A | for 3rd Row Seat | *B | except 3rd Row Seat |
| *C | for Standard Body 5th Row Seat | - | - |
for 3rd Row Seat:
Detach the claw and 2 guides and remove the rear seat inner leg cover.
Detach the 2 claws and 2 guides and remove the rear seat inner leg cover.
| *A | except 3rd Row Seat | *B | for Standard Body 5th Row Seat |
74617C
8.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)
Use the same procedure for the other assist grip plugs.
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the 2 claws and remove the assist grip plug.
|
Protective Tape |
74610A
9.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
Remove the 2 screws and assist grip sub-assembly.
79209
10.REMOVE NO. 2 SEATBACK BOARD SUB-ASSEMBLY (w/ Seatback Board)
Slide the No. 2 seatback board sub-assembly in the direction indicated by the arrow shown in the illustration and detach the 3 guides to remove it.
73179A
11.REMOVE SEAT BELT ANCHOR COVER CAP LH
Using a thin-bladed screwdriver with its tip wrapped in protective tape, detach the 2 claws and 3 guides and remove the seat belt anchor cover cap LH.
|
Protective Tape |
73344
12.REMOVE REAR SEAT SHOULDER BELT GUIDE LH
Using moulding remover A, detach the 2 claws.
Slide the part in the direction indicated by the arrow shown in the illustration and detach the 2 guides.
Remove the rear seat outer belt assembly from the gap in the rear seat shoulder belt guide LH to remove the rear seat shoulder belt guide LH.
| *a | Gap |
13.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR (except 2nd Row Seat)
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
14.DISCONNECT REAR SEAT OUTER BELT SUB-SUBASSEMBLY FLOOR ANCHOR (for 2nd Row Seat)
Use the same procedure as for the rear seat outer belt assembly floor anchor.
73373F
15.REMOVE REAR SEAT SHOULDER BELT HOLE COVER (w/o Seatback Board)
Remove the 3 hog rings.
Pull out the fastener.
Open the fastener.
Detach the 10 claws and 8 guides and remove the rear seat shoulder belt hole cover.
73136A
16.REMOVE SHOULDER BELT ANCHOR COVER LH
Remove the 2 screws and pull out the shoulder belt anchor cover LH.
Detach the outer seat belt assembly from the gap in the shoulder belt anchor cover LH and then remove the shoulder belt anchor cover LH.
| *a | Gap |
73375
17.REMOVE REAR SEAT SHOULDER BELT COVER LH
Slide the part in the direction indicated by the arrow shown in the illustration and detach the claw and guide.
Slide the part in the direction indicated by the arrow shown in the illustration and detach the 2 clamps.
Detach the outer seat belt assembly from the gap in the rear seat shoulder belt hole cover and then remove the rear seat shoulder belt cover LH.
| *a | Gap |
73370B
18.REMOVE REAR SEAT OUTER BELT ASSEMBLY (except 2nd Row Seat)
73302
19.REMOVE REAR SEAT OUTER BELT SUB-ASSEMBLY (for 2nd Row Seat)
Use the same procedure as for the rear seat outer belt assembly.
20.REMOVE REAR SEAT SHOULDER BELT COVER LH
Using a needle-nose pliers with the tips wrapped with protective tape, detach the 2 claws labeled A and remove the clip.
| *a | Claw A |
| *b | Claw B |
Detach the claw labeled B and guide and remove the rear seat shoulder belt cover LH.
79014
21.REMOVE NO. 1 SEATBACK COVER SUB-ASSEMBLY LH
w/ Seatback Board:
Remove the 3 hog rings.
Remove the 2 hog rings.
Remove the 2 hog rings and No. 1 seatback cover sub-assembly LH.
79018A
22.REMOVE NO. 1 SEATBACK PAD SUB-ASSEMBLY LH
Remove the No. 1 rear seatback pad sub-assembly LH.
73343
23.REMOVE REAR SEAT SHOULDER BELT GUIDE RH
Remove the 2 screws.
Detach the guide and remove the rear seat shoulder belt guide RH.
79012
24.REMOVE NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY LH
Detach the fastening tape and fold back the No. 1 seat cushion cover sub-assembly LH.
|
Fastening Tape |
for Type A:
Detach the 5 hooks.
for Type B:
Detach the 6 hooks.
for Long Body 5th Row Seat:
for Standard Body 4th Row Seat:
Pull out the strap of the No. 1 seat cushion cover sub-assembly LH from the No. 1 seat leg sub-assembly LH.
Remove the No. 1 seat cushion cover sub-assembly LH with pad from the No. 1 seat leg sub-assembly LH.
for Type A:
Detach the 3 pieces of fastening tape.
|
Fastening Tape |
for Type B:
Detach the piece of fastening tape.
|
Fastening Tape |
Remove the 6 hog rings and No. 1 seat cushion cover LH from the No. 1 seat cushion pad sub-assembly LH.
71868C
25.REMOVE REAR NO. 1 SEAT INNER CUSHION SHIELD LH
Remove the screw and rear No. 1 seat inner cushion shield LH.
71867M
26.REMOVE REAR NO. 1 SEAT INNER CUSHION SHIELD RH
Remove the screw and rear No. 1 seat inner cushion shield RH.
79967K
27.REMOVE REAR NO. 4 SEAT LEG SIDE COVER (for 2nd Row Seat)
Using a thin-bladed screwdriver with its tip wrapped with protective tape, detach the 3 claws and remove the rear No. 4 seat leg side cover.
|
Protective Tape |
79967B
28.REMOVE REAR NO. 2 SEAT LEG SIDE COVER (for 2nd Row Seat)
Slide the rear seat rear No. 2 seat leg side cover in the direction indicated by the arrow shown in the illustration and remove it.
79968
29.REMOVE REAR NO. 5 SEAT LEG SIDE COVER (for 2nd Row Seat)
Detach the 2 hooks and slide the rear No. 5 seat leg side cover in the direction indicated by the arrow shown in the illustration and remove it.
72345A
30.REMOVE RECLINING CONNECTING PIPE
Remove the reclining connecting pipe.
71875G
31.REMOVE SEAT RECLINING ADJUSTER INSIDE COVER LH (w/ Reclining Function)
Using a clip remover, remove the clip.
Detach the 4 guides and remove the seat reclining adjuster inside cover LH.
79290A
32.REMOVE NO. 2 SEATBACK SPRING ASSEMBLY LH
Remove the 2 bolts.
Detach the 2 guides and remove the No. 2 seatback spring assembly LH.