Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedures listed below are for RHD vehicles.
The procedure listed below is for 1st row to 7th row for long body, and 2nd row to 6th row for standard body.
2nd row seats are not installed to vehicles with cooling boxes.
The procedure listed below is a representative example.
Use the same procedure for all rows, unless otherwise specified.
1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for 1st Row Seat, w/ Pretensioner and Force Limiter)
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
2.REMOVE COOLING BOX (w/ Cool Box)
When removing the first row seat from vehicles with a cooling box installed, remove the cooling box assembly.
Click hereVehicle Interior>AIR CONDITIONING>COOLING BOX>REMOVAL
3.REMOVE REAR NO. 1 SEAT ASSEMBLY LH
for 1st Row Seat:
except 1st Row Seat:
73224
4.REMOVE FRONT SEAT BELT RETRACTOR COVER LH (for 1st Row Seat)
Detach the 2 clips and remove the front seat belt retractor cover LH from the front side trim cover LH.
Remove the front seat outer belt assembly LH from the gap in the front seat belt retractor cover LH to remove the front seat belt retractor cover LH.
73220
5.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (for 1st Row Seat)
Remove the bolt.
Detach the guide and disconnect the floor anchor of the front seat outer belt assembly LH.
Using a moulding remover D, detach the 2 claws and open the shoulder anchor cover.
Loosen the bolt and disconnect the shoulder anchor of the front seat outer belt assembly LH.
w/ Pretensioner and Force Limiter:
Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.
| *a | Protective Tape |
| *b | Locking Button |
Tape the screwdriver tip before use.
Remove the 2 bolts.
Detach the 2 guides and remove the front seat outer belt assembly LH.
71812K
6.REMOVE RECLINING ADJUSTER COVER LH (except 2nd Row Seat)
71876E
7.REMOVE RECLINING ADJUSTER INSIDE COVER LH (for 2nd Row Seat)
74617C
8.REMOVE ASSIST GRIP PLUG (w/ Assist Grip)
74610A
9.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
79209
10.REMOVE NO. 2 SEAT BACK BOARD SUB-ASSEMBLY (w/ Seatback Board)
73179A
11.REMOVE SEAT BELT ANCHOR COVER CAP LH
73344
12.REMOVE REAR SEAT SHOULDER BELT GUIDE LH
13.DISCONNECT REAR SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR (except 2nd Row Seat)
Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.
14.DISCONNECT REAR SEAT OUTER BELT SUB-ASSEMBLY FLOOR ANCHOR (for 2nd Row Seat)
Use the same procedure as for the rear seat outer belt assembly floor anchor.
73373F
15.REMOVE REAR SEAT SHOULDER BELT HOLE COVER (w/o Seatback Board)
73136A
16.REMOVE SHOULDER BELT ANCHOR COVER LH
73375
17.REMOVE REAR SEAT SHOULDER BELT COVER LH
73370B
18.REMOVE REAR SEAT OUTER BELT ASSEMBLY (except 2nd Row Seat)
Pull out the rear seat outer belt assembly from the hole in the No. 1 seatback cover sub-assembly LH as shown in the illustration.
Pull out the rear seat outer belt assembly from the No. 1 seatback spring assembly LH as shown in the illustration.
Remove the bolt.
Detach the 2 guides and remove the rear seat outer belt assembly.
73302
19.REMOVE REAR SEAT OUTER BELT SUB-ASSEMBLY (for 2nd Row Seat)
Pull out the rear seat outer belt sub-assembly from the hole in the No. 1 seatback cover sub-assembly LH as shown in the illustration.
Pull out the rear seat outer belt sub-assembly from the No. 1 seatback spring sub-assembly LH and No. 1 seatback cover sub-assembly LH as shown in the illustration.
Remove the bolt.
Detach the 2 guides and remove the rear seat outer belt sub-assembly.