Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY (for Single-Passenger Seat without 3 Point Type Seat Belt) › 2017.01–2021.01
RM2850E _58 Vehicle Interior _073189 SEAT _0356168 REAR SEAT ASSEMBLY(for Single-Passenger Seat without 3 Point Type Seat Belt) A

SEAT  REAR SEAT ASSEMBLY(for Single-Passenger Seat without 3 Point Type Seat Belt)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for RHD vehicles.

·

The procedure listed below is for 1st row to 7th row for long body, and 1st row to 6th row for standard body.

·

2nd row seats are not installed to vehicles with cooler boxes.

·

The procedure listed below is a representative example.

·

Use the same procedure for all rows, unless otherwisespecified.



PROCEDURE

Hide 79290A 1.INSTALL NO. 2 SEATBACK SPRING ASSEMBLY LH

a.
B473589E01
0.167,2.26 0.448,1.688 true 0.479,2.375 0.76,1.802 true 3.229,2.396 2.969,1.76 true 2.885,2.521 2.625,1.885 true 0.083,2.25 0.396,2.448 0.313,0.198 10 false *a 0.354,2.385 0.667,2.583 0.313,0.198 10 false *b 3.167,2.406 3.427,2.615 0.26,0.208 10 false *a 2.833,2.552 3.094,2.76 0.26,0.208 10 false *a

for Hi-back Seat Type

i.

Attach the 2 guides and temporarily install the No. 2 seatback spring assembly LH using the 4 bolts.

Text in Illustration
*a Bolt A
*b Bolt B

HINT:

Use bolt B as the installation bolt for the floor anchors of the rear seat inner belt assembly.



ii.

While pushing the No. 2 seatback spring assembly LH forward, tighten the 3 bolts labeled A

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)



iii.

Remove the bolt labeled B.



b.
B472796E01
0.167,2.25 0.406,1.74 true 0.469,2.323 0.708,1.813 true 3.229,2.229 3.021,1.74 true 2.958,2.323 2.75,1.833 true 0.052,2.24 0.365,2.438 0.313,0.198 10 false *a 0.396,2.333 0.708,2.531 0.313,0.198 10 false *b 3.177,2.25 3.427,2.438 0.25,0.188 10 false *a 2.875,2.354 3.188,2.552 0.313,0.198 10 false *b

except Hi-back Seat Type

i.

Attach the 2 guides and temporarily install the No. 2 seatback spring assembly LH using the 4 bolts.

Text in Illustration
*a Bolt A
*b Bolt B

HINT:

w/ Seat Belt:

Use bolt B as the installation bolt for the floor anchors of the rear seat inner belt assembly and seat inner belt assembly.



ii.

w/ Seat Belt:

While pushing the No. 2 seatback spring assembly LH forward, tighten the 2 bolts labeled A.

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)



iii.

Remove the 2 bolts labeled B.


iv.

w/o Seat Belt:

While pushing the No. 2 seatback spring assembly LH forward, tighten the 4 bolts.

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)




Hide 71875G 2.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER LH (w/ Reclining Function)

a.
B466384

Attach the 4 guides and install the seat reclining adjuster inside cover LH.


b.

Attach the clip.


Hide 72345A 3.INSTALL RECLINING CONNECTING PIPE

a.
B398774

Install the reclining connecting pipe.


Hide 79968 4.INSTALL REAR NO. 5 SEAT LEG SIDE COVER (for 2nd Row)

a.
B466238

Slide the rear No. 5 seat leg side cover in the direction indicated by the arrow shown in the illustration and attach the 2 hooks to install it.


Hide 79967B 5.INSTALL REAR NO. 2 SEAT LEG SIDE COVER (1st and 2nd Row)

a.
B466236

Slide the rear No. 2 seat leg side cover in the direction indicated by the arrow shown in the illustration and install it.


Hide 79967K 6.INSTALL REAR NO. 4 SEAT LEG SIDE COVER (1st and 2nd Row)

a.
B466234

Attach the 3 claws and install the rear No. 4 seat leg side cover.


Hide 71867M 7.INSTALL REAR NO. 1 SEAT INNER CUSHION SHIELD RH (for Hi-back Seat Type)

a.
B466383

Install the rear No. 1 seat inner cushion shield RH with the screw.


Hide 71868C 8.INSTALL REAR NO. 1 SEAT INNER CUSHION SHIELD LH (for Hi-back Seat Type)

a.
B457752

Install the rear No. 1 seat inner cushion shield LH with the screw.


Hide 79012 9.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY LH

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B466427E01
0.677,0.5 0.823,0.667 0.146,0.167 10 true A 0.885,0.552 1.031,0.719 0.146,0.167 10 true A 1.938,0.781 2.083,0.948 0.146,0.167 10 true B 2.104,0.833 2.25,1 0.146,0.167 10 true B 3.771,0.188 4.229,0.385 0.458,0.198 10 false A-A 5.573,0.208 6.031,0.406 0.458,0.198 10 false B-B



a.

Set the No. 1 seat cushion cover LH.


b.
B398790E01
0.594,3.167 0.375,3.76 true 1.792,3.76 2.271,2.729 2.271,2.729 2.531,2.729 true 1.51,0.844 1.708,0.979 0.198,0.135 10 true (1) 2.01,0.917 2.208,1.063 0.198,0.146 10 true (2) 0.979,0.813 1.177,0.948 0.198,0.135 10 true (3) 0.698,1.146 0.875,1.281 0.177,0.135 10 true (4) 2.458,1.177 2.635,1.323 0.177,0.146 10 true (5) 2.271,1.396 2.448,1.542 0.177,0.146 10 true (6) 0.292,3.813 0.458,3.979 0.167,0.167 10 false *a 2.583,2.625 2.75,2.792 0.167,0.167 10 false *b

Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly LH to the No. 1 seat cushion pad sub-assembly LH with 6 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seat cushion cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



c.
B466231E01
2.615,1.292 2.615,1.677 true 1.135,2.188 0.885,2.333 true 2.219,2.188 2.531,2.323 true 2.542,1.719 2.76,1.896 0.219,0.177 10 false *a 2.042,2.094 2.26,2.271 0.219,0.177 10 false *a 1.167,2.083 1.385,2.26 0.219,0.177 10 false *a

for Hi-back Seat Type:

i.

Attach the 3 pieces of fastening tape to install the strap of the No. 1 seat cushion cover sub-assembly LH as shown in the illustration.

Text in Illustration
*a Alignment Hole
V100145

Fastening Tape



d.

except Hi-back Seat Type:

i.

Attach the fastening tape to install the strap of the No. 1 seat cushion cover sub-assembly LH as shown in the illustration.

B472794E01
4.25,1.531 4.479,1.292 true 4.135,1.51 4.448,1.708 0.313,0.198 10 false *a

Text in Illustration
*a Alignment Hole
V100145

Fastening Tape


ii.

Install the strap of the No. 1 seat cushion cover sub-assembly LH from the No. 1 seat cushion pad LH.



e.

Set the No. 1 seat cushion cover sub-assembly LH with pad on the No. 1 seat leg sub-assembly LH.


f.
B466228

for Long Body 5th Row Seat:

for Standard Body 4th Row Seat:

i.

Pass the strap of the No. 1 seat cushion cover sub-assembly LH through the No. 1 seat leg sub-assembly LH.



g.
B466227E01
1.385,0.552 1.563,0.635 true 1.698,0.708 1.844,0.969 true 1.708,3.802 1.708,4.094 true 2.646,3.875 2.646,4.063 true 0.781,3.875 0.781,4.063 true 1.229,0.458 1.448,0.667 0.219,0.208 10 false *a 1.813,1 2.031,1.177 0.219,0.177 10 false *b 0.677,4.094 0.896,4.271 0.219,0.177 10 false *c 2.552,4.094 2.771,4.271 0.219,0.177 10 false *c 1.604,4.125 1.823,4.302 0.219,0.177 10 false *1

for Type A:

i.

Attach the 5 hooks to install the No. 1 seat cushion cover LH with pad to the No. 1 seat leg sub-assembly LH as shown in the illustration.

Text in Illustration
*1 No. 1 Seat Leg Sub-assembly LH
*a Frame Hole
*b Pad Hole
*c Hook



h.

for Type B:

i.

Attach the 6 hooks to install the No. 1 seat cushion cover sub-assembly LH with pad to the No. 1 seat leg sub-assembly LH as shown in the illustration.

B472792E01
2.094,0.177 2.833,0.333 true 2.854,0.417 3.229,0.5 true 2.26,2.448 2.365,2.125 2.365,2.125 2.49,2.125 true 2.979,2.479 3.083,2.156 3.083,2.156 3.208,2.156 true 3.656,2.448 3.76,2.125 3.76,2.125 3.885,2.125 true 1.906,0.073 2.219,0.271 0.313,0.198 10 false *a 3.281,0.448 3.594,0.646 0.313,0.198 10 false *b 2.542,2.031 2.854,2.229 0.313,0.198 10 false *c 3.229,2.073 3.542,2.271 0.313,0.198 10 false *1 3.917,2.042 4.229,2.24 0.313,0.198 10 false *c

Text in Illustration
*1 No. 1 Seat Leg Sub-assembly LH - -
*a Frame Hole *b Pad Hole
*c Hook - -



i.
B472789

Attach the fastening tape and close the No. 1 seat cushion cover sub-assembly LH.

Text in Illustration
V100145

Fastening Tape


Hide 79018A 10.INSTALL NO. 1 SEATBACK PAD SUB-ASSEMBLY LH

a.

Install the No. 1 rear seatback pad sub-assembly LH.

B473586E01
1.281,0.083 1.656,0.323 0.375,0.24 12 false *A 3.927,0.052 4.302,0.292 0.375,0.24 12 false *B 3.927,0.292 4.302,0.531 0.375,0.24 12 false *C

Text in Illustration
*A for Low-back Seat Type *B for Middle-back Seat Type
*C for Hi-back Seat Type - -


Hide 79014 11.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY LH

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B472797E01
0.406,0.063 0.781,0.302 0.375,0.24 12 false *A 2.906,0.042 3.281,0.281 0.375,0.24 12 false *B 5.094,0.031 5.469,0.271 0.375,0.24 12 false *C 0.875,0.781 1.031,0.938 0.156,0.156 10 true A 1.208,0.833 1.365,0.99 0.156,0.156 10 true A 1.844,0.927 2,1.083 0.156,0.156 10 true B 2.135,0.979 2.292,1.135 0.156,0.156 10 true B 3.385,0.99 3.542,1.146 0.156,0.156 10 true A 3.083,0.917 3.24,1.073 0.156,0.156 10 true A 1.365,0.042 1.521,0.198 0.156,0.156 10 true C 1.292,0.292 1.448,0.448 0.156,0.156 10 true C 3.396,0.615 3.552,0.771 0.156,0.156 10 true C 3.458,0.344 3.615,0.5 0.156,0.156 10 true C 5.604,0.615 5.76,0.771 0.156,0.156 10 true C 5.531,0.875 5.688,1.031 0.156,0.156 10 true C 5.198,1.063 5.354,1.219 0.156,0.156 10 true A 5.521,1.104 5.677,1.26 0.156,0.156 10 true A 3.927,1.073 4.083,1.229 0.156,0.156 10 true B 4.229,1.104 4.385,1.26 0.156,0.156 10 true B 6.063,1.167 6.219,1.323 0.156,0.156 10 true B 6.354,1.24 6.51,1.396 0.156,0.156 10 true B 1.979,2.344 2.365,2.521 0.385,0.177 10 true A-A 3.302,2.333 3.771,2.51 0.469,0.177 10 true B-B 5.167,2.396 5.594,2.552 0.427,0.156 10 true C-C

Text in Illustration
*A for Hi-back Seat Type *B for Middle-back Seat Type
*C for Low-back Seat Type - -



a.

Set the No. 1 seatback cover sub-assembly LH.


b.
B466385E01
1.917,3.823 2.25,3 2.25,3 2.458,3 true 0.458,2.583 0.844,2.865 true 2.292,1.604 2.49,1.781 0.198,0.177 10 false (2) 1.635,1.698 1.833,1.875 0.198,0.177 10 false (1) 0.292,2.458 0.49,2.635 0.198,0.177 10 false *a 2.49,2.896 2.688,3.073 0.198,0.177 10 false *b

Hi-back Seat Type:

i.

Using hog ring pliers, install the 2 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



ii.
B466386E01
1.854,3.823 2.219,2.833 2.219,2.833 2.51,2.833 true 0.844,2.865 0.5,2.417 true 1.635,2.135 1.802,2.292 0.167,0.156 10 false (1) 2.24,2.031 2.406,2.188 0.167,0.156 10 false (2) 0.375,2.26 0.542,2.417 0.167,0.156 10 false *a 2.594,2.74 2.76,2.896 0.167,0.156 10 false *b

Using hog ring pliers, install the 2 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



iii.
B457780

w/ Seatback Board:

Close the fastener.


iv.

Insert the end of the fastener inside the seat cover material as shown in the illustration.

B457779



c.

Using hog ring pliers, install the No. 1 seatback cover sub-assembly LH with 3 new hog rings.

B472787E01
4.771,1.042 5.188,0.625 true 5.938,1.042 6.25,0.573 true 0.448,0.031 0.823,0.271 0.375,0.24 12 false *A 2.688,0.052 3.063,0.292 0.375,0.24 12 false *B 4.604,0.99 4.917,1.188 0.313,0.198 10 false *a 6.229,0.396 6.542,0.594 0.313,0.198 10 false *b

Text in Illustration
*A for Hi-back Seat Type *B for Middle-back Seat Type
*a Cutout *b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



d.
B401471E01
0.313,3.948 0.552,3.188 true 1.604,4.469 1.854,4.177 true 1.344,0.531 1.802,0.729 0.458,0.198 10 false (1) 1.833,0.594 2.292,0.792 0.458,0.198 10 false (2) 1.354,1.083 1.813,1.281 0.458,0.198 10 false (3) 1.771,1.167 2.229,1.365 0.458,0.198 10 false (4) 0.229,3.938 0.688,4.135 0.458,0.198 10 false *a 1.417,4.406 1.875,4.604 0.458,0.198 10 false *b

for Middle-back Seat Type:

i.

Using hog ring pliers, install the 4 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



ii.
B473585E01
0.333,3.76 0.615,3.156 true 1.573,4.479 1.844,4.198 false 0.229,3.75 0.542,3.948 0.313,0.198 10 false *a 1.385,4.417 1.698,4.615 0.313,0.198 10 false *b

Using hog ring pliers, install the No. 1 seatback cover sub-assembly LH with 3 new hog rings.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.




e.
B401472E01
0.281,3.823 0.594,3.146 true 1.792,4.469 2.031,4.198 false 1.469,0.781 1.927,0.979 0.458,0.198 10 false (1) 1.885,0.865 2.344,1.063 0.458,0.198 10 false (2) 0.177,3.833 0.635,4.031 0.458,0.198 10 false *a 1.625,4.417 2.083,4.615 0.458,0.198 10 false *b

for Low-back Seat Type:

i.

Using hog ring pliers, install the 2 new hog rings in the order shown in the illustration.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



ii.
B473585E01
0.333,3.76 0.615,3.156 true 1.573,4.479 1.844,4.198 false 0.229,3.75 0.542,3.948 0.313,0.198 10 false *a 1.385,4.417 1.698,4.615 0.313,0.198 10 false *b

Using hog ring pliers, install the No. 1 seatback cover sub-assembly LH with 3 new hog rings.

Text in Illustration
*a Cutout
*b Hog Ring Pliers

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly LH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.




Hide 79209 12.INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY (w/ Seatback Board)

a.
B466457

Slide the part in the direction indicated by the arrow shown in the illustration and attach the 3 guides to install the No. 2 seatback board sub-assembly.


Hide 74130C 13.INSTALL REAR ASH RECEPTACLE ASSEMBLY (w/ Ashtray)

a.
B290049

Install the rear ash receptacle plate with the 2 screws.


Hide 74145A 14.INSTALL REAR ASH RECEPTACLE PLATE (w/ Ashtray)

a.
B290136

Install the rear ash receptacle assembly.


Hide 74610A 15.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

a.
B398693

Install the assist grip sub-assembly with 2 new screws.


Hide 74617C 16.INSTALL ASSIST GRIP PLUG (w/ Assist Grip)

HINT:

Use the same procedure for the other assist grip plugs.


a.
B398728

Attach the 2 claws to install the assist grip plug.


Hide 71149K 17.INSTALL REAR SEAT INNER LEG COVER

a.
B472784

for 3rd Row Seat:

i.

Attach the claw and 2 guides to install the rear seat inner leg cover.



b.
B472785

except 3rd Row Seat:

i.

Attach the 2 claws and 2 guides to install the rear seat inner leg cover.



c.

Install the screw.

B472783E01
0.656,0.417 1.031,0.656 0.375,0.24 12 false *A 4.469,0.375 4.844,0.615 0.375,0.24 12 false *B

Text in Illustration
*A for 3rd Row Seat *B except 3rd Row Seat


Hide 71148N 18.INSTALL REAR SEAT OUTER LEG COVER

a.

except 3rd Row Seat:

i.

Attach the 9 claws, 2 guides and 4 clips to install the rear seat outer leg cover.

B472780



b.

for 3rd Row Seat:

i.

Attach the 11 claws, guide and 2 clips to install the rear seat outer leg cover.

B472782



c.

Install the 3 screws in the order shown in the illustration.

B472778E02
1.083,0.406 1.458,0.646 0.375,0.24 12 false *A 4.667,0.333 5.042,0.573 0.375,0.24 12 false *B 0.677,1.781 1.135,1.979 0.458,0.198 10 false (1) 3.365,2.01 3.823,2.208 0.458,0.198 10 false (2) 2.479,2.219 2.938,2.417 0.458,0.198 10 false (3) 4.167,1.656 4.625,1.854 0.458,0.198 10 false (1) 6.531,1.958 6.99,2.156 0.458,0.198 10 false (2) 5.885,2.167 6.344,2.365 0.458,0.198 10 false (3)

Text in Illustration
*A except 3rd Row Seat *B for 3rd Row Seat


Hide 72379 19.INSTALL SEAT RECLINING HANDLE BELT (for Reclining Function)

a.

Install the seat reclining handle belt to the No. 2 seatback spring assembly LH.

B466396


Hide 71812K 22.INSTALL RECLINING ADJUSTER COVER LH

a.
B466397

for Hi-back Seat Type:

i.

w/ Reclining Function:

Pass the seat reclining handle belt through the hole in the reclining adjuster cover LH.



b.

for Type A:

i.

Attach the 7 claws and 3 guides to install the reclining adjuster cover LH.

B472769



c.

for Type B:

i.

Attach the 7 claws and 2 guides to install the reclining adjuster cover LH.

B472800



d.
B466483

Install the 2 screws.


e.
B472773

except Hi-back Seat Type:

i.

Attach the guide to install the reclining adjuster cover LH.


ii.

Install the 2 screws.



Hide 71876E 23.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

for Hi-back Seat Type:

i.

w/o Reclining Function:

Attach the 7 claws and 2 guides to install the reclining adjuster inside cover LH.

B466507



b.

w/ Reclining Function:

i.

Attach the 6 claws and 2 guides to install the reclining adjuster inside cover LH.

B466509



c.
B466482

Install the 2 screws.


d.
B472772

except Hi-back Seat Type:

i.

Attach the guide to install the reclining adjuster inside cover LH.


ii.

Install the 2 screws.