Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY (for 2-Passenger Seat with Separate Type Seatback)
RM2850E _58 Vehicle Interior _073189 SEAT _0356169 REAR SEAT ASSEMBLY(for 2-Passenger Seat with Separate Type Seatback) A

SEAT  REAR SEAT ASSEMBLY(for 2-Passenger Seat with Separate Type Seatback)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

The procedure listed below is for 1st row to 7th row for long body, and 1st row to 6th row for standard body.

·

The procedure listed below is a representative example.

·

Use the same procedure for all rows, unless otherwise specified.



PROCEDURE

Hide 79180A 1.INSTALL NO. 1 SEATBACK SPRING ASSEMBLY RH

a.
B457763E01
0.635,3.146 0.813,3.313 0.177,0.167 10 false *b 0.104,0.865 0.302,1.042 0.198,0.177 10 true *a 0.531,0.646 0.719,0.813 0.188,0.167 10 true *b 0.167,2.885 0.354,3.042 0.188,0.156 10 true *a

Attach the 2 guides and temporarily install the No. 1 seatback spring assembly RH with the 4 bolts.

Text in Illustration
*a Bolt A
*b Bolt B

HINT:

Use the installation bolt for the floor anchors of the rear seat belt inner assembly and rear seat belt outer assembly as bolt B.



b.

While pushing the No. 1 seatback spring assembly RH forward, tighten the 2 bolts A.

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)



c.

Remove the 2 bolts B.


Hide 79190A 2.INSTALL NO. 1 SEATBACK SPRING ASSEMBLY LH

HINT:

Use the same procedure described for the RH side.


Hide 71875F 3.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH (w/ Reclining Function)

a.
B457756

Attach the 4 guides to install the reclining adjuster inside cover RH.


b.

Install the clip.


Hide 71876F 4.INSTALL SEAT RECLINING ADJUSTER INSIDE COVER RH (w/ Reclining Function)

HINT:

Use the same procedure described for the RH side.


Hide 73380F 5.INSTALL REAR SEAT INNER BELT ASSEMBLY

HINT:

Use the same procedure as for the rear seat inner belt assembly.


a.
B457761E01
0.448,1.458 1.094,1.458 true 1.5,1.823 1.635,1.969 true 0.26,1.385 0.573,1.583 0.313,0.198 10 false *a 1.635,1.969 1.896,2.146 0.26,0.177 10 false *a

Install the rear seat inner belt assembly with the bolt.

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)


NOTICE:

The rear seat inner belt assembly must not overlap the location.


Text in Illustration
*a Location


Hide 72995A 6.INSTALL REAR SEAT COVER

a.
B457759

Pass the rear seat inner belt assembly through the hole in the rear seat cover.


b.
B457757

Attach the fastening tape and install the rear seat cover.

Text in Illustration
V100145

Fastening Tape


Hide 72345A 7.INSTALL RECLINING CONNECTING PIPE

a.
B398703

Install the reclining connecting pipe.


Hide 71873D 8.INSTALL REAR SEAT LOWER CUSHION SHIELD RH

a.
B457755

Install the rear seat lower cushion shield RH with the screw.


Hide 71874M 9.INSTALL REAR SEAT LOWER CUSHION SHIELD LH

a.

Attach the 6 claws to install the rear seat lower cushion shield LH.


b.

Install the screw.

B457754


Hide 71867N 10.INSTALL REAR NO. 1 SEAT INNER CUSHION SHIELD RH

a.
B457752

Install the rear No. 1 seat inner cushion shield RH with the screw.


Hide 71868C 11.INSTALL REAR NO. 1 SEAT INNER CUSHION SHIELD LH

a.
B466363E01
0.844,0.5 1.219,0.74 0.375,0.24 12 false *A

w/ Seatback Board:

i.

Install the rear No. 1 seat inner cushion shield LH with the 2 screws.

Text in Illustration
*A w/ Seatback Board



b.

w/o Seatback Board:

i.

Install the rear No. 1 seat inner cushion shield LH with the screw.



Hide 79021 12.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B466426E01
0.625,0.458 0.75,0.625 0.125,0.167 10 true A 0.438,0.438 0.563,0.604 0.125,0.167 10 true A 2.219,0.885 2.344,1.052 0.125,0.167 10 true B 2.438,0.896 2.563,1.063 0.125,0.167 10 true B 3.75,0.167 4.104,0.323 0.354,0.156 10 false A-A 5.667,0.167 6.021,0.323 0.354,0.156 10 false B-B



a.

Set the No. 2 seat cushion cover sub-assembly RH in place.


b.
B398727E01
1.677,4.417 1.813,4.177 true 0.396,2.792 0.563,2.906 true 0.25,2.698 0.49,2.885 0.24,0.188 10 false *a 1.573,4.427 1.813,4.615 0.24,0.188 10 false *b 1.885,1.052 2.094,1.219 0.208,0.167 10 true (1) 1.781,1.531 1.99,1.698 0.208,0.167 10 true (2) 1.656,0.99 1.865,1.156 0.208,0.167 10 true (3) 1.406,1.458 1.615,1.625 0.208,0.167 10 true (4) 2.198,1.021 2.406,1.188 0.208,0.167 10 true (5) 2.521,1.083 2.729,1.25 0.208,0.167 10 true (6) 1.385,0.885 1.594,1.052 0.208,0.167 10 true (7) 1.094,0.813 1.302,0.979 0.208,0.167 10 true (8) 2.906,1.365 3.115,1.531 0.208,0.167 10 true (9) 2.646,1.719 2.896,1.885 0.25,0.167 10 true (10) 0.74,0.823 0.99,0.99 0.25,0.167 10 true (11) 0.375,1.115 0.625,1.281 0.25,0.167 10 true (12)

Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly RH to the No. 2 seat cushion pad sub-assembly RH with 12 new hog rings in the order shown in the illustration.

NOTICE:
·

Do not dirty or damage the No. 2 seat cushion cover sub-assembly RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 2 seat cushion cover sub-assembly RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*a Cutout
*b Hog Ring Pliers


c.
B457751E01
0.781,0.646 1.281,0.521 true 2.156,1.292 2.427,1.167 true 1.302,1.531 1.469,1.271 1.469,1.271 1.698,1.542 true 2.583,1.521 2.927,1.26 2.927,1.26 2.979,1.531 true 1.573,3.208 1.552,2.688 true 1.427,1.125 1.646,1.302 0.219,0.177 10 false *a 2.458,1.104 2.677,1.281 0.219,0.177 10 false *a 2.896,1.135 3.115,1.313 0.219,0.177 10 false *a 1.302,0.427 1.521,0.604 0.219,0.177 10 false *a

for 1-leg Type:

i.

Attach the 6 pieces of fastening tape.

Text in Illustration
*a Alignment Hole
V100145

Fastening Tape



d.
B466459E01
0.771,0.646 1.24,0.469 true 2.156,1.281 2.49,1.198 true 1.281,0.354 1.594,0.552 0.313,0.198 10 false *a 2.531,1.094 2.844,1.292 0.313,0.198 10 false *a

for 2-leg Type:

i.

Attach the 2 pieces of fastening tape.

Text in Illustration
*a Alignment Hole
V100145

Fastening Tape



e.

Set the No. 2 seat cushion cover sub-assembly RH with pad on the No. 1 seat leg sub-assembly RH.


f.
B473608

for 2-leg Type 5th Row Seat:

i.

Pass the strap of the No. 1 seat cushion cover sub-assembly RH through the No. 1 seat leg sub-assembly RH.



g.

Attach the 9 hooks to install the No. 2 seat cushion cover RH with pad to the No. 1 seat leg sub-assembly RH as shown in the illustration.

B457749E01
4.427,3.479 4.427,3.313 false 5.094,3.531 5.094,3.365 false 3.729,3.531 3.729,3.365 false 4.49,0.448 5.094,0.208 true 3.76,0.792 4.396,0.583 true 4.333,3.51 4.646,3.708 0.313,0.198 10 false *1 5.135,0.104 5.448,0.302 0.313,0.198 10 false *a 3.594,0.75 3.906,0.948 0.313,0.198 10 false *b 3.625,3.531 3.938,3.729 0.313,0.198 10 false *c 5.01,3.521 5.323,3.719 0.313,0.198 10 false *c

Text in Illustration
*1 No. 1 Seat Leg Sub-assembly RH - -
*a Frame Hole *b Pad Hole
*c Hook - -


h.
B457747

Attach the fastening tape and close the No. 2 seat cushion cover RH.

Text in Illustration
V100145

Fastening Tape


Hide 73343 13.INSTALL REAR SEAT SHOULDER BELT GUIDE RH

HINT:

Use the same procedure for the other rear seat shoulder belt guides RH.


a.
B457745

Attach the guide to install the rear seat shoulder belt guide RH.


b.

Install the 2 screws.


Hide 79017A 14.INSTALL NO. 1 SEATBACK PAD SUB-ASSEMBLY RH

a.
B457744

Install the No. 1 seatback pad sub-assembly RH.


Hide 79018A 15.INSTALL NO. 1 SEATBACK PAD SUB-ASSEMBLY LH

HINT:

Use the same procedure described for the RH side.


Hide 79013 16.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY RH

HINT:
·

When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>PRECAUTION

·

Align the seam allowance in a single direction as shown in the illustration.

B466425E01
2.823,0.188 3.281,0.385 0.458,0.198 10 false A-A 4.313,0.177 4.771,0.375 0.458,0.198 10 false B-B 6.073,0.208 6.531,0.406 0.458,0.198 10 false C-C 0.656,0.427 0.802,0.594 0.146,0.167 10 true A 0.802,0.458 0.948,0.625 0.146,0.167 10 true A 1.01,0.021 1.156,0.188 0.146,0.167 10 true C 0.885,0.167 1.031,0.333 0.146,0.167 10 true C 1.417,0.583 1.563,0.75 0.146,0.167 10 true B 1.563,0.625 1.708,0.792 0.146,0.167 10 true B



a.

Set the No. 1 seatback cover sub-assembly RH in place.


b.
B457743E01
0.5,2.531 0.865,2.854 true 2.156,3.323 1.906,3.823 true 2.031,1.698 2.219,1.854 0.188,0.156 10 false (1) 1.365,1.604 1.552,1.76 0.188,0.156 10 false (2) 0.333,2.417 0.521,2.583 0.188,0.167 10 false *a 2.146,3.198 2.333,3.365 0.188,0.167 10 false *b

Using hog ring pliers, install the No. 1 seatback cover sub-assembly RH to the No. 1 seatback pad sub-assembly RH with 2 new hog rings in the order shown in the illustration.

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*a Cutout
*b Hog Ring Pliers


c.
B457741E01
0.542,2.448 0.896,2.844 true 2.146,3.406 1.896,3.823 true 1.531,2.031 1.729,2.188 0.198,0.156 10 false (2) 2.135,2.135 2.333,2.292 0.198,0.156 10 false (1) 0.365,2.344 0.583,2.51 0.219,0.167 10 false *a 2.135,3.24 2.354,3.406 0.219,0.167 10 false *b

Using hog ring pliers, install the 2 new hog rings in the order shown in the illustration.

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*a Cutout
*b Hog Ring Pliers


d.
B457739E01
1.615,3.771 1.906,3.219 true 0.563,2.906 0.385,2.729 true 0.26,2.594 0.469,2.781 0.208,0.188 10 false *a 1.865,3.094 2.073,3.281 0.208,0.188 10 false *b

w/ Seatback Board:

i.

Using hog ring pliers, install the No. 1 seatback cover sub-assembly RH with 3 new hog rings.

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*a Cutout
*b Hog Ring Pliers



Hide 79014 17.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY LH

HINT:

Use the same procedure described for the RH side.


Hide 18.INSTALL REAR SEAT SHOULDER BELT COVER RH

a.
B466429

Attach the guide and claw to install the rear seat shoulder belt cover RH.


b.

Attach the clip.


Hide 19.INSTALL REAR SEAT SHOULDER BELT COVER LH

HINT:

Use the same procedure described for the RH side.


Hide 73350C 21.INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY

HINT:

Use the same procedure as for the rear seat outer belt assembly.


Hide 73373D 22.INSTALL REAR SEAT SHOULDER BELT HOLE COVER RH

a.
B457732E01
1.542,1.104 1.792,0.729 true 1.771,0.604 2.083,0.802 0.313,0.198 10 false *a

Install the rear seat outer belt assembly through the gap in the rear seat shoulder belt hole cover RH.

Text in Illustration
*a Gap


b.
B457731

Slide the part in the direction indicated by the arrow shown in the illustration to attach the 2 clamps.


c.
B457729

Slide the part as shown in the illustration, attach the claw and guide and install the rear seat shoulder belt hole cover RH.


Hide 73375B 23.INSTALL REAR SEAT SHOULDER BELT HOLE COVER LH

HINT:

Use the same procedure described for the RH side.


Hide 73135A 24.INSTALL SHOULDER BELT ANCHOR COVER RH

a.
B457726E01
1.406,0.615 1.688,0.906 false 1.219,0.479 1.531,0.677 0.313,0.198 10 false *a

Install the rear seat outer belt assembly through the gap in the shoulder belt anchor cover RH.

Text in Illustration
*a Gap


b.
B457725

Install the shoulder belt anchor cover RH with the 2 screws.


Hide 73136A 25.INSTALL SHOULDER BELT ANCHOR COVER LH

HINT:

Use the same procedure described for the RH side.


Hide 73375M 26.INSTALL REAR SEAT SHOULDER BELT HOLE COVER (w/o Seatback Board)

HINT:

Use the same procedure for the other rear seat shoulder belt hole covers.


a.
B457782

Attach the 10 claws and 8 guides to install the rear seat shoulder belt hole cover.


b.
B457780

Close the fastener.


c.

Insert the end of the fastener inside the seat cover material as shown in the illustration.

B457779


d.
B457777E01
0.385,2.76 0.552,2.906 true 2.219,2.833 1.979,2.833 1.979,2.833 1.604,3.771 true 0.24,2.646 0.438,2.813 0.198,0.167 10 false *a 2.281,2.729 2.521,2.927 0.24,0.198 10 false *b

Using hog ring pliers, install the No. 1 seatback cover sub-assembly RH with 3 new hog rings.

NOTICE:
·

Do not dirty or damage the No. 1 seatback cover sub-assembly RH.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly RH.



HINT:

Install the hog rings at the cutouts if they are there.


Text in Illustration
*a Cutout
*b Hog Ring Pliers


Hide 27.CONNECT REAR SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR

a.

Check that the rear seat outer belt assembly RH is not twisted.


b.
B457720E01
1.698,1.354 2.677,1.354 true 2.104,1.667 2.438,1.667 2.438,1.667 2.438,1.365 true 2.708,1.271 3.021,1.469 0.313,0.198 10 false *a

Install the the floor anchor of the rear seat outer belt assembly with the bolt.

Torque:

42 N*m (428 kgf*cm, 31 ft.*lbf)


NOTICE:

The rear seat outer belt assembly must not overlap the location.


Text in Illustration
*a Location


Hide 28.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY FLOOR ANCHOR

HINT:

Use the same procedure as for the rear seat outer belt assembly floor anchor.


Hide 73373A 29.INSTALL REAR SEAT SHOULDER BELT COVER RH

a.
B466404E01
1.906,1.802 1.667,1.177 true 1.854,1.813 2.094,2.021 0.24,0.208 10 false *a

Install the rear seat outer belt assembly through the gap in the rear seat shoulder belt cover RH.

Text in Illustration
*a Gap


b.
B457724

Slide the part in the direction indicated by the arrow shown in the illustration and attach the 2 guides.


c.

Attach the 2 claws to install the rear seat shoulder belt cover RH.


Hide 73375 30.INSTALL REAR SEAT SHOULDER BELT COVER LH

HINT:

Use the same procedure described for the RH side.


Hide 73178A 31.INSTALL SEAT BELT ANCHOR COVER CAP

a.
B457722

Attach the 3 guides and 2 claws to install the seat belt anchor cover cap.


Hide 73179A 32.INSTALL SEAT BELT ANCHOR COVER CAP LH

HINT:

Use the same procedure as for the seat belt anchor cover cap.


Hide 79209 33.INSTALL NO. 2 SEATBACK BOARD SUB-ASSEMBLY (w/ Seatback Board)

HINT:

Use the same procedure for the other No. 2 seatback board sub-assemblies.


a.
B466457

Slide the part the part in the direction indicated by the arrow shown in the illustration and attach the 3 guides to install the No. 2 seatback board sub-assembly.


Hide 74610A 34.INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

HINT:

Use the same procedure for the other assist grip sub-assemblies.


a.
B398693

Install the assist grip sub-assembly with 2 new screws.


Hide 74617C 35.INSTALL ASSIST GRIP PLUG (w/ Assist Grip)

HINT:

Use the same procedure for the other assist grip plugs.


a.
B398728

Attach the 2 claws to install the assist grip plug.


Hide 71148C 36.INSTALL REAR SEAT OUTER LEG COVER (for 2-leg Type)

a.
B466447

Attach the 2 claws and 2 guides to install the rear seat outer leg cover.


b.

Install the screw.


Hide 71149R 37.INSTALL REAR SEAT INNER LEG COVER (for 2-leg Type)

a.
B466446

Attach the 2 guides, 9 claws and 3 clips to install the rear seat outer leg cover.


b.
B466444E02
0.281,0.917 0.74,1.115 0.458,0.198 10 false (1) 3,1.479 3.333,1.698 0.333,0.219 10 false (2) 2,1.521 2.458,1.719 0.458,0.198 10 false (3)

Install the 3 screws in the order shown in the illustration.


Hide 79967J 38.INSTALL REAR NO. 4 SEAT LEG SIDE COVER (for 7th Row Seat with 4-Passenger Seat)

a.
B457775

Attach the hook and fastening tape to install the rear No. 4 seat leg side cover.

Text in Illustration
V100145

Fastening Tape


b.
B457774

Attach the 3 pieces of fastening tape.

Text in Illustration
V100145

Fastening Tape


Hide 71149K 39.INSTALL REAR SEAT INNER LEG COVER

a.
B457713

for 1st Row Seat with Step:

i.

Attach the claw and 2 guides to install the rear seat inner leg cover.


ii.

Install the screw.



b.

except 1st Row Seat with Step:

i.

Attach the 2 claws and 2 guides to install the rear seat inner leg cover.


ii.

Install the screw.

B466443E01
0.073,0.063 0.448,0.302 0.375,0.24 12 false *A 3.573,0.083 3.948,0.323 0.375,0.24 12 false *B

Text in Illustration
*A except 1st Row Seat with Step *B for Standard Body 1-leg Type 5th Row Seat without Sub Seat



Hide 71148N 40.INSTALL REAR SEAT OUTER LEG COVER

a.
B466455

for 1st Row Seat with Step:

i.

Attach the 10 claws and 4 clips to install the rear seat outer leg cover.


ii.
B466453E02
2.781,1.396 3.24,1.594 0.458,0.198 10 false (1) 0.417,1.365 0.875,1.563 0.458,0.198 10 false (4) 1.531,1.927 1.99,2.125 0.458,0.198 10 false (2) 0.604,1.656 1.063,1.854 0.458,0.198 10 false (3)

Install the 4 screws in the order shown in the illustration.



b.
B457712

except 1st Row Seat with Step:

i.

Attach the 2 guides, 9 claws and 4 clips to install the rear seat outer leg cover.


ii.
B457710E01
2.927,1.25 3.115,1.417 0.188,0.167 10 false (1) 0.688,1.729 0.875,1.896 0.188,0.167 10 false (2) 1.896,1.958 2.083,2.125 0.188,0.167 10 false (3)

Install the 3 screws in the order shown in the illustration.



Hide 72379 41.INSTALL SEAT RECLINING HANDLE BELT (w/ Reclining Function)

HINT:

Use the same procedure for the other seat reclining handle belts.


a.

Install the seat reclining handle belt to the No. 1 seatback spring assembly RH.

B457706


Hide 71812C 42.INSTALL RECLINING ADJUSTER COVER LH

a.
B457704

w/ Reclining Function:

i.

Pass the seat reclining handle belt through the hole in the reclining adjuster cover LH.



b.
B473640

for 1-leg Type, 7th Row Seat with 4-Passenger Seat:

i.

Attach the 7 claws and 3 guides to install the reclining adjuster cover LH.



c.
B473641

for 2-leg Type:

i.

Attach the 7 claws and 2 guides to install the reclining adjuster cover LH.



d.
B466414E01
3.135,1.125 3.406,1.323 0.271,0.198 12 false *A

w/ Seatback Board:

i.

Install the screw.



e.

w/o Seatback Board:

i.

Install the 2 screws.

Text in Illustration
*A w/o Seatback Board



Hide 71811C 43.INSTALL RECLINING ADJUSTER COVER RH

a.
B457699

w/ Reclining Function:

i.

Pass the seat reclining handle belt through the hole in the reclining adjuster cover RH.



b.
B473642

for 1-leg Type, 7th Row Seat with 4-Passenger Seat:

i.

Attach the 7 claws and 3 guides to install the reclining adjuster cover RH.



c.
B473643

for 2-leg Type:

i.

Attach the 7 claws and 2 guides to install the reclining adjuster cover RH.



d.
B473636

Install the 2 screws.


Hide 44.INSTALL SUB SEAT ASSEMBLY (w/ Sub Seat)