Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY (for Single-Passenger Seat with 3 Point Type Seat Belt)
RM2850E _58 Vehicle Interior _073190 SEAT BELT _0356179 REAR SEAT OUTER BELT ASSEMBLY(for Single-Passenger Seat with 3 Point Type Seat Belt) N

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY(for Single-Passenger Seat with 3 Point Type Seat Belt)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

HINT:

When scrapping vehicles equipped with a seat belt pretensioner or disposing of a seat belt (with a seat belt pretensioner), always deploy the procedures described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the service dept. of the distributor.


CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a seat belt with a pretensioner that has not been deployed.

·

The seat belt produces an exploding sound when the pretensioner deploys, so perform the operation outdoors where it will not disturb local residents.

·

When deploying a seat belt pretensioner, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical interference.

·

When deploying a seat belt pretensioner, perform the operation at least 10 m (32.8 ft.) away from the seat belt.

·

The seat belt becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a seat belt with a deployed pretensioner.

·

Do not apply water, etc. to a seat belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.



Hide 73220 2.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN INSTALLED IN VEHICLE)

NOTICE:
·

When disposing of a seat belt with a pretensioner, never deploy the pretensioner in the customer's vehicle.

·

Be sure to follow the procedure listed below when deploying a seat belt pretensioner.



a.
B050515E58
0.875,1.188 0.802,1 false 0.615,0.844 0.906,1.042 0.292,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the seat belt pretensioner, always use the specified SST.


i.
B050511E24
0.854,1.281 1.167,1.51 false 2.26,0.906 2.573,0.906 false 0.531,1.219 0.823,1.417 0.292,0.198 10 false SST 2.635,0.802 3.094,1 0.458,0.198 10 false *a

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

Text in Illustration
*a Battery

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B050514E36
1.479,0.552 1.302,0.302 false 0.99,0.219 1.448,0.417 0.458,0.198 10 false SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




b.

Disconnect the seat belt pretensioner connector.

i.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.




iii.
B464715E01
0.292,0.781 0.51,0.354 true 1.063,1.24 0.75,0.667 true 0.188,0.792 0.5,0.99 0.313,0.198 10 false *a 1.021,1.271 1.333,1.469 0.313,0.198 10 false *b

Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

Text in Illustration
*a Protective Tape
*b Locking Button

HINT:

Tape the screwdriver tip before use.




c.
B473612E02
1.208,1.76 1.208,1.542 false 2.198,1.76 2.198,1.542 false 1.073,1.771 1.531,1.969 0.458,0.198 10 false SST 2.052,1.76 2.51,1.958 0.458,0.198 10 false SST

Connect SST.

i.

Connect 2 SST, and then connect them to the seat belt pretensioner.

SST
09082-00700  09082-00802  (09082-10801, 09082-20801)

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
B517819E01
1.698,0.854 1.938,0.552 false 0.458,1.167 0.677,1.427 false 1.594,1.781 1.906,1.979 0.313,0.198 10 false *a 1.948,0.417 2.26,0.615 0.313,0.198 10 false *b 0.167,1.073 0.688,1.313 0.521,0.24 10 false SST

Move SST at least 10 m (32.8 ft.) away from the front of the vehicle.

Text in Illustration
*a 10 m or more
*b Battery


iii.

Close all the doors and windows of the vehicle.

NOTICE:

Do not damage the SST wire harness.




d.

Deploy the seat belt pretensioner.

i.

Confirm that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




e.
B349004

Dispose of the seat belt.

i.

Remove the seat belt and SST.


ii.

Place the seat belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The seat belt becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a seat belt with a deployed pretensioner.

·

Do not apply water, etc. to a seat belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle, deploy the seat belt pretensioner, and then scrap the vehicle with the seat belt installed.




Hide 73220 3.DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)

NOTICE:

Be sure to follow the procedure listed below when deploying a seat belt pretensioner.



b.
B349005E01
2.042,0.26 2.354,0.458 0.313,0.198 10 false *a 0.979,0.635 1.292,0.833 0.313,0.198 10 false *b

Wind the seat belt webbing with the retractor.

Text in Illustration
*a Cut
*b 100 mm


c.

When the seat belt webbing is sufficiently wound, cut the seat belt webbing approximately 100 mm (3.94 in.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in correlation with how much the seat belt webbing is wound.



d.
B050515E57
0.844,0.844 1.052,1.188 false 0.521,0.76 0.979,0.958 0.458,0.198 10 false SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the seat belt pretensioner, always use the specified SST.


i.
B050511E24
0.854,1.281 1.167,1.51 false 2.26,0.906 2.573,0.906 false 0.531,1.219 0.823,1.417 0.292,0.198 10 false SST 2.635,0.802 3.094,1 0.458,0.198 10 false *a

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.

Text in Illustration
*a Battery

HINT:

At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in a later step.



ii.
B050514E36
1.479,0.552 1.302,0.302 false 0.99,0.219 1.448,0.417 0.458,0.198 10 false SST

Press the SST deployment switch and check that the LED of the SST deployment switch illuminates.

CAUTION:

If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST.




e.
B473612E02
1.208,1.76 1.208,1.542 false 2.198,1.76 2.198,1.542 false 1.073,1.771 1.531,1.969 0.458,0.198 10 false SST 2.052,1.76 2.51,1.958 0.458,0.198 10 false SST

Connect SST.

i.

Connect 2 SST, and then connect them to the seat belt pretensioner.

SST
09082-00700  09082-00802  (09082-10801, 09082-20801)

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.



ii.
B473613E01
1.188,1.615 1.188,1.365 false 2.313,1.625 2.313,1.375 false 1.052,1.646 1.615,1.885 0.563,0.24 10 false SST 2.198,1.646 2.76,1.885 0.563,0.24 10 false SST

Place the seat belt on the ground and cover it with a tire and wheel assembly.

NOTICE:
·

Position the seat belt as shown in the illustration.

·

Use a scrap tire and wheel assembly when disposing of a seat belt pretensioner.




iii.

Position and hold SST at least 10 m (32.8 ft.) away from the tire and wheel assembly.

NOTICE:

Do not damage the SST wire harness.




f.
B517835E01
1.073,0.781 1.365,0.781 false 0.552,1.302 0.844,1.302 false 1.615,1.677 1.927,1.875 0.313,0.198 10 false *a 1.375,0.688 1.729,0.875 0.354,0.188 10 false *b 0.917,1.219 1.375,1.479 0.458,0.26 10 false SST

Deploy the seat belt pretensioner.

Text in Illustration
*a 10 m or more
*b Battery

i.

Check that no one is within a 10 m (32.8 ft.) radius of the tire and wheel assembly.


ii.

Connect the red clip of SST to the battery positive (+) terminal and the black clip to the battery negative (-) terminal.


iii.

Press the SST deployment switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner will deploy at the same time as the LED of SST illuminates.




g.
B349004

Dispose of the seat belt.

i.

Remove the tire and wheel assembly and SST.


ii.

Place the seat belt in a plastic bag, tie the end tightly, and dispose of it in the same way as other general parts.

CAUTION:
·

The seat belt becomes very hot when the pretensioner is deployed, so leave it untouched for at least 30 minutes after the pretensioner is deployed.

·

Use gloves and safety glasses when handling a seat belt with a deployed pretensioner.

·

Do not apply water, etc. to a seat belt with a deployed pretensioner.

·

Always wash your hands with water after completing the operation.