Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356199 FRONT PASSENGER AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 82142 1.INSTALL NO. 2 INSTRUMENT PANEL WIRE

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B468046E01
1.167,2.677 1.417,2.156 1.417,2.156 1.594,2.156 true 1.646,2.083 1.958,2.281 0.313,0.198 10 false *a

Attach the wire harness clamp to install the No. 2 instrument panel wire.


d.

Connect the airbag connector and push the lock button.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


Text in Illustration
*a Lock Button


Hide 73970A 2.INSTALL INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

a.
B471846E01
1.583,0.479 1.844,0.479 true 2.531,0.594 2.781,0.594 true 1.323,0.781 1.583,0.479 1.583,0.479 1.792,0.833 true 2.313,0.885 2.531,0.594 2.531,0.594 2.74,0.948 true 3.031,1.333 3.125,1.49 3.125,1.49 2.969,1.552 true 0.76,0.896 0.531,0.875 0.531,0.875 0.604,1.083 true 0.813,1.51 0.979,1.667 0.979,1.667 1.24,1.583 true 1.917,1.688 2.083,1.844 2.083,1.844 2.344,1.76 true 0.906,1.677 1.229,1.875 0.323,0.198 10 false (1) 2.01,1.854 2.333,2.052 0.323,0.198 10 false (1) 0.333,0.75 0.656,0.948 0.323,0.198 10 false (2) 3.146,1.385 3.406,1.604 0.26,0.219 10 true (2) 1.885,0.385 2.208,0.583 0.323,0.198 10 false (3) 2.854,0.531 3.177,0.729 0.323,0.198 10 false (3)

Attach the 12 claws to set the instrument panel passenger airbag assembly.

HINT:

Attach the claws in the order shown in the illustration.



b.
B471847E01
1.729,2.469 1.729,2.198 1.729,2.198 1.927,2.198 true 2.698,2.469 2.698,2.219 2.698,2.219 2.927,2.219 true 1.969,2.135 2.281,2.333 0.313,0.198 10 false *a 2.969,2.156 3.281,2.354 0.313,0.198 10 false *b

Install the instrument panel passenger airbag assembly with the 2 bolts.

Torque:

20N*m{ 204kgf*cm , 15 ft.*lbf }



c.

Connect the airbag connector and check that the slider is in the lock position.

Text in Illustration
*a Slider
*b Lock Position

NOTICE:

Securely lock the airbag connector.


HINT:

If the slider is not in the lock position, the airbag connector is not completely connected. Disconnect the airbag connector, check the airbag connector and spiral cable sub-assembly terminals and connector housings for deformation or foreign matter, and then reconnect the airbag connector.



d.

Check that the lock slider is in the lock position.


Hide 88650N 3.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 55433B 4.INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION