Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT PASSENGER AIRBAG ASSEMBLY
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0356199 FRONT PASSENGER AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT PASSENGER AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

HINT:

When scrapping a vehicle equipped with an SRS or disposing of the instrument panel passenger airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs during the airbag deployment, contact the Service Dept. of the distributor.


CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a instrument panel passenger airbag assembly with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the instrument panel passenger airbag assembly.

·

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a instrument panel passenger airbag assembly with a deployed airbag.

·

Do not apply water etc. to a instrument panel passenger airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



Hide 73970A 2.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When Installed in Vehicle)

NOTICE:
·

When disposing of the instrument panel passenger airbag assembly, never use the customer's vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



a.
C110371E70
0.938,1.198 0.938,0.698 0.938,0.698 0.635,0.698 true 0.323,0.625 0.781,0.823 0.458,0.198 10 false SST

Check the function of SST (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL).

SST
09082-00700  



c.

Disconnect the cable from the negative (-) battery terminal.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL


d.

Remove the lower No. 2 instrument panel finish panel.

Click hereVehicle Interior>INTERIOR PANEL>INSTRUMENT PANEL SAFETY PAD>REMOVAL


e.

Remove the air conditioning amplifier.

Click hereVehicle Interior>AIR CONDITIONING>AIR CONDITIONING AMPLIFIER>REMOVAL


f.

Disconnect the airbag connector.

i.
B477087E01
0.667,2.396 0.729,2.135 0.729,2.135 0.979,2.135 true 1.021,2.052 1.333,2.25 0.313,0.198 10 false *a

Slide the slider to release the lock, and then disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


Text in Illustration
*a Lock Slider



g.

Install SST.

i.
B468047E01
2.979,1.323 2.979,1.01 true 1.979,1.573 1.979,1 true 1.604,1.573 1.604,0.99 1.604,0.99 3.052,0.99 true 3.073,0.917 3.396,1.125 0.323,0.208 10 false SST

Connect the SST connector to the No. 2 instrument panel wire.

SST
09082-00700  09082-00760  

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
B468048E01
2.385,1.625 2.844,1.625 true 2.073,1.542 2.531,1.74 0.458,0.198 10 false SST 1.927,1.875 2.219,2.073 0.292,0.198 10 false *a

Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

Text in Illustration
*a 10 m or more


iii.

While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



h.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
·

Before deployment, make sure that no one is near the vehicle.

·

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a instrument panel passenger airbag assembly with a deployed airbag.

·

Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.



iii.

Disconnect the red clip of SST from the battery positive (+) terminal and the black clip of SST from the negative (-) terminal.


iv.

Disconnect the SST (09082-00700) connector from the SST.



Hide 73970A 3.DISPOSE OF INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (When Not Installed in Vehicle)

NOTICE:

Be sure to follow the procedure detailed below when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E71
0.719,0.667 0.958,0.667 0.958,0.667 0.958,1.198 true 0.417,0.583 0.875,0.781 0.458,0.198 10 false SST

Check the function of SST (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL).

SST
09082-00700  


b.

Remove the instrument panel passenger airbag assembly (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT PASSENGER AIRBAG ASSEMBLY>REMOVAL).

CAUTION:
·

Before removing the instrument panel passenger airbag assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the auxiliary battery negative (-) terminal.

·

When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.




c.

Remove the airbag door.

i.
B468049

Insert moulding remover B into the side of the airbag door facing the rear of the vehicle and bend moulding remover B to detach the 3 hooks.


ii.

Raise the instrument panel passenger airbag assembly to detach the 3 hooks on the side of the airbag door facing the front of the vehicle and remove the airbag door from instrument panel passenger airbag assembly.



d.

Install SST.

i.
B471842

After connecting the following SST to each other, connect them to the instrument panel passenger airbag assembly.

SST
09082-00700  09082-00802  (09082-10801, 09082-40800)



e.
B515005E02
1.865,1.615 1.865,1.25 true 2.656,0.51 2.969,0.708 0.313,0.198 10 false *a 1.813,1.635 2.125,1.833 0.313,0.198 10 false *b

Using braided wire, tie the instrument panel passenger airbag assembly to an unneeded tire.

Text in Illustration
*a Wire Diameter
*b Stripped Wire Section

Wire:

Stripped wire section

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the instrument panel passenger airbag assembly, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the stripped wire section: Area = 3.14 x (Diameter)2 / 4


i.

Position the instrument panel passenger airbag assembly inside the tire with the airbag deployment side facing inside.

Minimum tire size:

Must exceed the following dimensions

Width

185 mm (7.28 in.)

Inner diameter

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the instrument panel passenger airbag assembly may break loose when the airbag is deployed.

·

Always tie down the instrument panel passenger airbag assembly with the airbag deployment side facing inside the tire as shown in the illustration.



NOTICE:

The tires may be damaged by the airbag deployment, so use unneeded tires.


B477084E01
1.104,1.781 2.208,2.063 false 3.146,1.958 3.458,2.156 0.313,0.198 10 false *b 2.833,0.5 3.146,0.698 0.313,0.198 10 false *a 0.938,1.667 1.25,1.865 0.313,0.198 10 false *c

Text in Illustration
*a Width *b Inner Diameter
*c Deployment Side - -



f.

Place the tires.

i.
B477085E01
0.885,2.031 1.292,1.99 true 0.698,1.938 1.01,2.135 0.313,0.198 10 false *a

Place at least 2 tires under the tire to which the instrument panel passenger airbag assembly is tied.

Text in Illustration
*a Tires (2 or more)


ii.

Place at least 2 tires onto the tire to which the instrument panel passenger airbag assembly is tied. The top tire should have a wheel installed.

NOTICE:
·

Do not place the SST connector under the tire because it could be damaged.

·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.




iii.

Tie the tires together with the 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




g.

Install SST.

i.

Connect the SST connector.

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.



ii.
B477086E01
1.01,3.052 1.323,3.25 0.313,0.198 10 false *a

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

Text in Illustration
*a 10 m or more



h.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel to which the instrument panel passenger airbag assembly is tied.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.


HINT:

The airbag is deployed as the LED of the SST activation switch comes on.



iv.

Disconnect the red clip of SST from the battery positive (+) terminal and the black clip of SST from the negative (-) terminal.


v.

Disconnect the SST connector from the SST.



i.
C122262

Dispose of the instrument panel passenger airbag assembly.

CAUTION:
·

The instrument panel passenger airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling an instrument panel passenger airbag assembly with an deployed airbag.

·

Do not apply water etc. to an instrument panel passenger airbag assembly with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the instrument panel passenger airbag assembly from the tire.


ii.

Place the instrument panel passenger airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.