Home › Vehicle Interior › AIR CONDITIONING › COMPRESSOR (for N04C-VQ)
RM2850E _58 Vehicle Interior _073207 AIR CONDITIONING _0356288 COMPRESSOR(for N04C-VQ) A

AIR CONDITIONING  COMPRESSOR(for N04C-VQ)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.
I103302E03
0.885,3.135 1.198,2.948 true 0.365,0.396 0.677,0.594 0.313,0.198 10 false *1 1.906,0.385 2.219,0.583 0.313,0.198 10 false *2 1.229,2.833 1.542,3.031 0.313,0.198 10 false *3 0.729,3.438 1.042,3.635 0.313,0.198 10 false A 2.25,3.427 2.563,3.625 0.313,0.198 10 false B

When replacing the compressor and magnet clutch with a new one, gradually discharge the refrigerant gas from the service valve. Then drain the following amount of oil from the new compressor and magnet clutch before installation, so that the amount of oil contained in it is the same as that in the compressor and magnet clutch to be replaced.

Text in Illustration
*1 New Compressor and Magnet Clutch
*2 Removed Compressor and Magnet Clutch
*3 Drain Extra Oil (A - B)

HINT:

New compressor and magnet clutch are filled with sufficient oil for the whole cycle. Therefore, it is necessary to drain excess oil from the condenser and cooling unit.


Standard:

(The amount of oil inside a new compressor and magnet clutch: 400 (+/- 30) cc (13.5 (+/- 1.01) fl.oz.)) - (The amount of oil in the removed compressor and magnet clutch) = The amount of oil to be removed from the new compressor and magnet clutch.


NOTICE:
·

When checking the compressor oil level, observe the precautions for cooler removal/ installation.

·

If a new compressor and magnet clutch is installed without removing the excess oil, the amount of oil in the system becomes too large. This prevents heat exchange in the refrigerant cycle and causes refrigeration failure.

·

If the amount of oil in the removed compressor and magnet clutch is too small, check for oil leakage.

·

Use ND-OIL8 compressor oil.




b.

If draining the compressor oil is difficult, drain the compressor oil using the following procedure:

i.

Rotate the pulley, and drain the compressor oil.

NOTICE:
·

Do not allow the magnet clutch rotor to come into contact with compressor oil.

·

If the magnet clutch rotor is rotated, refrigerant or compressor oil might splash out. Thus, keep your face away from the compressor port.





Hide 88720A 2.CONNECT AIR CONDITIONING HOSE AND ACCESSORY

a.

Remove the attached vinyl tape from the suction hose.


b.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnet clutch.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the suction hose.


d.

Connect the suction hose to the compressor and magnet clutch with the bolt.

Torque:

9.8 N*m (100 kgf*cm, 87 in.*lbf)



e.

Remove the attached vinyl tape from the discharge hose.


f.

Apply sufficient compressor oil to a new O-ring and the fitting surface of the compressor and magnet clutch.

Compressor oil:

ND-OIL8 or equivalent



g.

Install the O-ring onto the discharge hose.


h.

Connect the discharge hose to the compressor and magnet clutch with the bolt.

Torque:

9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 3.INSTALL COMPRESSOR AND MAGNET CLUTCH

a.

Install the compressor and magnet clutch together with the air conditioning hose and accessory with the 4 bolts.

Torque:

47 N*m (475 kgf*cm, 34 ft.*lbf)


NOTICE:

Do not apply excessive force to the air conditioning hose and accessory.



b.

Connect the connector.


c.

Install the air conditioning hose and accessory with the 2 bolts.

Torque:

47 N*m (475 kgf*cm, 34 ft.*lbf)



Hide 88310A 4.INSTALL NO. 1 V (COOLER COMPRESSOR TO CRANKSHAFT PULLEY) BELT

Hide 7.INSPECT REFRIGERANT LEAK