Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check" screen of the GTS (Click here(Click here))

·

Communication stop history for "Skid Control (ABS/VSC/TRAC)" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Skid Control (ABS/VSC/TRAC)" is 6 or more.) (Click here(Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table" (Click here(Click here))


·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Power source circuit of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) ground circuit

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C358921E02
1.521,2.063 2.969,2.292 1.448,0.229 10 false from IG1-NO.1 Relay 3.792,1.938 5.24,2.167 1.448,0.229 10 false ECU-IG1 NO.3 0.219,1.635 0.677,1.833 0.458,0.198 10 false A91 0.219,1.823 1.448,2.219 1.229,0.396 10 false No. 3 CAN Junction Connector 5.167,3.813 5.625,4.01 0.458,0.198 10 false A71 5.156,4 6.76,4.375 1.604,0.375 10 false Brake Actuator Assembly (Skid Control ECU) 5.594,0.979 6.208,1.177 0.615,0.198 10 false CANH 5.604,1.396 6.219,1.594 0.615,0.198 10 false CANL 5.625,2.094 6.24,2.292 0.615,0.198 10 false IG1 5.615,2.625 6.229,2.823 0.615,0.198 10 false GND2 5.615,3.115 6.229,3.313 0.615,0.198 10 false GND1 1.583,0.875 1.74,1.073 0.156,0.198 10 false 2 1.594,1.292 1.75,1.49 0.156,0.198 10 false 4 5.302,0.875 5.615,1.073 0.313,0.198 10 false 22 5.302,1.292 5.615,1.49 0.313,0.198 10 false 10 5.302,1.979 5.615,2.177 0.313,0.198 10 false 12 5.313,3.01 5.625,3.208 0.313,0.198 10 false 25 5.344,2.521 5.656,2.719 0.313,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Drive the vehicle for approximately 3 seconds or more at a speed of 15 km/h (9 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly (skid control ECU) connector.


c.
C358900E02
1.458,0.083 1.854,0.313 0.396,0.229 2.083,0.792 2.135,0.156 2.135,0.156 2.302,0.156 true 2.104,1 2.313,0.333 2.313,0.333 2.469,0.333 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.531,0.115 1.875,0.302 0.344,0.188 10 false A71 2.354,0.073 2.969,0.271 0.615,0.198 10 false CANL 2.542,0.25 3.156,0.448 0.615,0.198 10 false CANH

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-22 (CANH) - A71-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (HARNESS AND CONNECTOR)

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (HARNESS AND CONNECTOR)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.
C358900E03
1.448,0.052 1.885,0.323 0.438,0.271 0.719,0.896 0.719,0.135 0.719,0.135 0.875,0.135 false 2.385,0.813 2.469,0.208 2.469,0.208 2.667,0.208 false 0.604,1.281 0.604,1.896 0.604,1.896 0.792,1.896 false 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 1.552,0.094 1.885,0.313 0.333,0.219 10 false A71 0.938,0.063 1.552,0.26 0.615,0.198 10 false GND2 0.865,1.823 1.479,2.021 0.615,0.198 10 false GND1 2.75,0.135 3.365,0.333 0.615,0.198 10 false IG1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A71-12 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Tester Connection
A71-1 (GND2) - Body ground Always Below 1 Ω
A71-25 (GND1) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])

Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR