Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM › 2017.01–2021.01
RM2850E _57 Power Source / Network _073263 CAN COMMUNICATION _0356688 CAN COMMUNICATION SYSTEM J

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  Center Airbag Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Center Airbag Sensor Communication Stop Mode Either condition is met:
·

Communication stop for "Airbag" is indicated on the "Communication Bus Check" screen of the GTS (Click here(Click here)).

·

Communication stop history for "Airbag" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Airbag" is 6 or more.) (Click here(Click here))

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" (Click here(Click here)).


·

Airbag ECU assembly CAN main wire or connector

·

Power source circuit of airbag ECU assembly

·

Airbag ECU assembly ground circuit

·

Airbag ECU assembly



WIRING DIAGRAM

C348756E27
0.156,1.708 0.615,1.906 0.458,0.198 10 false A91 0.146,1.885 4.427,2.083 4.281,0.198 10 false No. 3 CAN Junction Connector 1.698,2.333 4.604,2.531 2.906,0.198 10 false from IG2-NO.2 Relay 3.844,2.208 5.219,2.406 1.375,0.198 10 false A/BAG-IG2 5.604,0.802 6.219,1 0.615,0.198 10 false CANH 5.615,1.594 6.229,1.792 0.615,0.198 10 false CANL 5.625,2.354 6.24,2.552 0.615,0.198 10 false IG2 5.625,3.385 6.24,3.583 0.615,0.198 10 false E2 5.625,4.115 6.24,4.313 0.615,0.198 10 false E1 5.396,4.771 6.01,4.969 0.615,0.198 10 false A58 5.385,4.969 6.906,5.229 1.521,0.26 10 false Airbag ECU Assembly 1.677,0.771 1.833,0.969 0.156,0.198 10 false 5 1.677,1.385 1.833,1.583 0.156,0.198 10 false 7 5.354,0.792 5.604,0.99 0.25,0.198 10 false 13 5.354,1.385 5.604,1.583 0.25,0.198 10 false 22 5.365,2.26 5.615,2.458 0.25,0.198 10 false 21 5.365,3.281 5.615,3.479 0.25,0.198 10 false 26 5.375,4.01 5.625,4.208 0.25,0.198 10 false 25

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 10 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>PRECAUTION).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG ECU ASSEMBLY CAN MAIN WIRE)
a.
C227515E12
0.292,0.865 0.656,1.125 0.365,0.26 2.01,1.031 2.552,0.635 2.552,0.635 2.698,0.635 true 2.125,1.375 2.521,1.823 2.521,1.823 2.688,1.823 true 2.771,0.563 3.385,0.76 0.615,0.198 10 false CANH 2.75,1.74 3.365,1.938 0.615,0.198 10 false CANL 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.344,0.896 0.802,1.094 0.458,0.198 10 false A58

Disconnect the cable from the negative (-) battery terminal and wait for at least 90 seconds.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-13 (CANH) - A58-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Airbag ECU Assembly)


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPLACE CAN MAIN WIRE CONNECTED TO AIRBAG ECU ASSEMBLY (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C227515E13
0.354,0.938 0.729,1.188 0.375,0.25 1.292,1.906 1.427,1.906 1.427,1.906 1.656,1.344 true 2.177,1.917 2.031,1.917 2.031,1.917 1.781,1.354 true 2.521,1.708 2.385,1.708 2.385,1.708 2.24,1.365 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 2.604,1.615 3.063,1.813 0.458,0.198 10 false IG2 2.24,1.833 2.698,2.031 0.458,0.198 10 false E1 1.052,1.833 1.51,2.031 0.458,0.198 10 false E2 0.417,0.969 0.875,1.167 0.458,0.198 10 false A58

Connect the cable to the negative (-) battery terminal and wait for at least 2 seconds.

NOTICE:

When connecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A58-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-25 (E1) - Body ground Always Below 1 Ω
A58-26 (E2) - Body ground Always Below 1 Ω



Text in Illustration
*a Rear view of wire harness connector
(to Airbag ECU Assembly)

Result:
Proceed to
OK
NG



OK

NG

REPLACE HARNESS AND CONNECTOR