There may be a short circuit between the CAN main bus lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Detection Item | Trouble Area |
|---|---|
| Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus lines ·
ECM ·
Central gateway ECU (network gateway ECU) ·
No. 66 junction connector |
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communicationsystem related DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, themalfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wireharness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 66 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connect to |
|---|---|---|---|
| A85-1 (CANH) - A85-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| A85-3 (CANH) - A85-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| *a | Front view of wire harness connector
(to No. 66 Junction Connector) |
| *b | to ECM |
| *c | to Central Gateway ECU (Network Gateway ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU CAN main wire) | B |
| NG (ECM CAN main wire) | C |
A
B
C
Reconnect the A85 No. 66 junction connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J51-18 (CA4H) - J51-17 (CA4L) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A85 No. 66 junction connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A56-7 (CANH) - A56-1 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-17 (CANH) - A52-28 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A53-33 (CANH) - A53-34 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| *A | for N04C-VQ, N04C-VL |
| *B | for N04C-UH |
| *C | for 2TR-FE |
| *a | Front view of wire harness connector
(to ECM) |
| Result | Proceed to |
|---|---|
| OK (for N04C-VQ) | A |
| OK (for N04C-UH) | B |
| OK (for 2TR-FE) | C |
| OK (for N04C-VL) | D |
| NG | E |
A
B
C
D
E