Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1421  Open or Short in Master Cylinder Pressure Sensor  C1423  Master Cylinder Pressure Sensor Zero Point Low Malfunction  C1424  Master Cylinder Pressure Sensor Output Malfunction  C142A  Master Cylinder Pressure Sensor Internal Malfunction  C1449  Master Cylinder Output Value Malfunction  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
C1421 Either of the following is detected:
1.

When voltage at terminal +BS is 9.5 V or higher, power supply voltage of master cylinder pressure sensor is continuously low for 1 second or more.

2.

When master cylinder pressure sensor power supply voltage has risen, master cylinder pressure sensor has overheated or overcurrent of master cylinder pressure sensor continues for 0.1 seconds or more.

3.

When +BS terminal voltage is 9.5 to 17.4 V, there is no communication with master cylinder pressure sensor continuously for 0.1 seconds or more.


Master cylinder pressure sensor (Brake actuator assembly)
C1423 Master cylinder pressure is below -0.744 MPa (-7.6 kgf/cm2, -107 psi) for 5 seconds or more. Master cylinder pressure sensor (Brake actuator assembly)
C1424 Either of the following is detected:
1.

When vehicle speed is 7 km/h (4.3 mph) or more and master cylinder pressure exceeds 1.764 MPa (18.0 kgf/cm2, 255 psi), master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more continuously for 60 seconds.

2.

When vehicle speed is 7 km/h (4.3 mph) and master cylinder pressure is 2.45 MPa (25.0 kgf/ cm2, 355 psi) or more, master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more continuously for 30 seconds.

3.

Master cylinder pressure does not increase 0.048 MPa (0.5 kgf/cm2, 6.9 psi) or more 5 times or more while vehicle speed decreases from 40 km/h (25 mph) to 0 km/h (0 mph).

4.

When vehicle speed is 10 km/h (6 mph) or more, noise in master cylinder pressure value occurs 7 times or more in 5 seconds.

5.

When vehicle speed is 7 km/h (4.3 mph) or more, braking is performed (stop light switch assembly is ON) and master cylinder pressure differential value is below 20 MPa/s, difference between master cylinder pressure estimated from vehicle deceleration and master cylinder pressure sensor input value is large for 1 second or more 5 times or more.


Master cylinder pressure sensor (Brake actuator assembly)
C142A Either of the following is detected:
1.

Master cylinder pressure is 23.328 MPa (237.8 kgf/cm2, 3382 psi) or more continuously for 0.1 seconds.

2.

Master cylinder temperature is 150°C (302°F) or more continuously for 0.1 seconds.


Master cylinder pressure sensor (Brake actuator assembly)
C1449 Master cylinder pressure sensor invalid condition continues for 0.2 seconds or more. Master cylinder pressure sensor (Brake actuator assembly)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the brake actuator assembly (master cylinder pressure sensor) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (w/ Brake pedal Load Sensing Switch)>REMOVAL).


Result:
Proceed to
NEXT



NEXT

END