The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.
The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1425 | When voltage at terminal +BS is 9.5 to 17.4 V, open circuit occurs between STP terminal circuits A and B for 0.3 seconds or more. | ·
STOP NO. 5 fuse ·
Stop light switch assembly ·
Wire harness or connector ·
Skid control ECU (Brake actuator assembly) |
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed | On |
| Brake pedal released | Off |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch assembly / ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.
The GTS displays ON or OFF according to brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch to ON.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1425 is not output | A |
| DTC C1425 is output | B |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Remove the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>REMOVAL).
Inspect the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).
The stop light switch assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Reinstall the stop light switch assembly (Click hereVehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSTALLATION).
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A71 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A71-35 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 8 to 14 V |
| A71-35 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A71 skid control ECU (brake actuator assembly) connector.
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1425 is not output | A |
| DTC C1425 is output | B |
If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (w/ Brake pedal Load Sensing Switch)>REMOVAL).
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A71 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A71-35 (STP) - Body ground | Stop light switch assembly on (Brake pedal depressed) | 8 to 14 V |
| A71-35 (STP) - Body ground | Stop light switch assembly off (Brake pedal released) | Below 1.5 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG