The solenoid relay supplies power to the solenoids.
The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by the self-diagnosis performed when the engine starts running.
The solenoid relay is housed in the skid control ECU in the actuator assembly.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C146E | Either of the following is detected:
1.
When voltage at terminal +BS is 9.5 V or higher and solenoid relay is ON, relay contact is OFF continuously for 0.22 seconds or more. 2.
When solenoid relay is turned on and voltage at +BS terminal is below 9.5 V, relay contact does not turn on after 0.22 seconds or more. |
·
ABS NO. 2 fuse ·
Wire harness or connector ·
Skid control ECU (Brake actuator assembly) |
| C146F | Immediately after ignition switch turned to ON and solenoid relay is OFF, relay contact is ON continuously for 4.5 seconds or more. | Skid control ECU (Brake actuator assembly) |
Refer to DTCs C1225, C1468, C1469, C146A and C146B (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1225).
When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When C1241 and/or C1417 is output together with C146E and/or C146F, inspect and repair the trouble areas indicated by C1241 and/or C1417 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241 and/or Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417).
Turn the ignition switch off.
Make sure that there is no looseness in the locking part and connecting part of the connectors.
Disconnect the A71 skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A71-38 (+BS) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A71-25 (GND1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).
The solenoid circuits are in the skid control ECU (brake actuator assembly).
Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed.
Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).
Reconnect the A71 skid control ECU (brake actuator assembly) connector.
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C146E and C146F are not output | A |
| DTC C146E and/or C146F are output | B |
If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly), with the ignition switch ON and the stop light switch off, the ECU performs self-diagnosis of the motor and solenoid circuits.
If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.
If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
The DTCs were probably output due to a bad connection of the connector terminal.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B