Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356689 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch (vehicle stability control switch) turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF indicator light and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C291298E36
3.688,3.385 5.313,3.75 1.625,0.365 10 false VSC OFF Switch (Vehicle Stability Control Switch) 3.688,3.229 4.031,3.427 0.344,0.198 10 false J92 3.656,2.76 4,2.958 0.344,0.198 10 false 6 4.719,2.76 5.063,2.958 0.344,0.198 10 false 9 5.719,2.76 6.063,2.958 0.344,0.198 10 false 33 5.979,2.885 6.396,3.104 0.417,0.219 10 false CSW 5.573,4.01 7.156,4.417 1.583,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.573,3.833 5.979,4.052 0.406,0.219 10 false A71 5.969,0.917 6.375,1.135 0.406,0.219 10 false CANL 5.969,1.75 6.427,1.979 0.458,0.229 10 false CANH 0.917,0.938 1.365,1.156 0.448,0.219 10 false CANL 0.906,1.75 1.354,1.969 0.448,0.219 10 false CANH 2.896,4.344 4.635,4.563 1.74,0.219 10 false : CAN Communication Line 0.302,4.083 1.479,4.479 1.177,0.396 10 false Combination Meter Assembly 0.302,3.927 0.646,4.125 0.344,0.198 10 false J1 1.375,0.75 1.719,0.948 0.344,0.198 10 false 22 1.375,1.563 1.719,1.76 0.344,0.198 10 false 23 5.708,0.75 6.052,0.948 0.344,0.198 10 false 10 5.698,1.563 6.042,1.76 0.344,0.198 10 false 22 3.885,2.76 4.229,2.958 0.344,0.198 10 false E 4.5,2.74 4.844,2.938 0.344,0.198 10 false +

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output (Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/VSC off mode / Normal, TRC OFF or VSC OFF Normal: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-


g.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch (vehicle stability control switch) operation.

Standard:
Switch Operation Mode Condition Display TRC OFF Indicator Light VSC OFF Indicator Light
Not pressed Normal Does not come on Does not come on
Pressing the VSC OFF switch (vehicle stability control switch) TRC OFF Comes on Does not come on
Pressing and holding the VSC OFF switch (vehicle stability control switch) VSC OFF Comes on Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display is normal C



A

4.PERFORM ACTIVE TEST USING GTS (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)

B

C

4.PERFORM ACTIVE TEST USING GTS (TRC OFF INDICATOR LIGHT AND VSC OFF INDICATOR LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.


f.

According to the display on the GTS, perform the Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
TRC(TRAC) OFF Indicator Light TRC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped
VSC OFF Indicator Light VSC OFF indicator light Indicator light ON/OFF Observe combination meter assembly
Vehicle condition: Vehicle stopped


g.

Check the TRC OFF indicator light and VSC OFF indicator light in the combination meter assembly turn on or off in accordance with GTS operation.

OK:

The TRC OFF indicator light and VSC OFF indicator light turn on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

5.INSPECT VEHICLE STABILITY CONTROL SWITCH

NG

7.INSPECT COMBINATION METER ASSEMBLY
5.INSPECT VEHICLE STABILITY CONTROL SWITCH
a.

Turn the ignition switch off.


b.

Remove the VSC OFF switch (vehicle stability control switch) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (w/ VSC)>REMOVAL).


c.

Inspect the VSC OFF switch (vehicle stability control switch) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (w/ VSC)>INSPECTION).

OK:

The VSC OFF switch (vehicle stability control switch) operates normally.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (VEHICLE STABILITY CONTROL SWITCH - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE VEHICLE STABILITY CONTROL SWITCH

6.CHECK HARNESS AND CONNECTOR (VEHICLE STABILITY CONTROL SWITCH - BRAKE ACTUATOR ASSEMBLY)
a.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-33 (CSW) - J92-9 (+) Always Below 1 Ω
A71-33 (CSW) or J92-9 (+) - Body ground Always 10 kΩ or higher
J92-6 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform the Active Test of the combination meter assembly using the GTS (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The TRC OFF indicator light and VSC OFF indicator light turn on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG