Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › 2017.01–2019.08
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2.

*1: w/o Airbag System

*2: w/ Airbag System


DTC No. DTC Detection Condition Trouble Area
C1381 At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

ECU-IG1 NO. 3 fuse*1

·

A/BAG-IG2 fuse*2

·

Acceleration sensor (Yaw rate sensor)*1

·

Acceleration sensor (Airbag ECU assembly)*2

·

Wire harness or connector



*1: w/o Airbag System

*2: w/ Airbag System


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2, perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

*1: w/o Airbag System

*2: w/ Airbag System


·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK VEHICLE
a.

Check the Airbag System.


Result:
Result Proceed to
w/o Airbag System A
w/ Airbag System B



A

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)

B

5.CHECK TERMINAL VOLTAGE (IG2 TERMINAL)
2.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A72 yaw rate and acceleration sensor (yaw rate sensor) connector.


c.

Turn the ignition switch to ON.


d.
C208309E46
1.448,0.188 1.875,0.438 0.427,0.25 2.344,1.75 1.76,1.219 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.531,0.219 1.875,0.417 0.344,0.198 10 false A72 2.292,1.792 2.521,1.99 0.229,0.198 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A72-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Yaw Rate Sensor))


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C208309E47
1.427,0.25 1.906,0.479 0.479,0.229 0.792,1.667 1.198,1.198 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 1.542,0.281 1.927,0.479 0.385,0.198 10 false A72 0.604,1.719 1.021,1.906 0.417,0.188 10 false GND

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A72-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Yaw Rate Sensor))


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A72 yaw rate and acceleration sensor (yaw rate sensor) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 3 km/h (2 mph) or more for at least 10 seconds.


f.

Check if the same DTC is output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1381 is not output. A
DTC C1381 is output. B


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).




A

B

5.CHECK TERMINAL VOLTAGE (IG2 TERMINAL)
NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.
C239271E35
0.271,0.646 0.792,0.896 0.521,0.25 0.688,2.698 1.031,2.188 true 0.26,0.198 0.573,0.396 0.313,0.198 10 false *a 0.396,0.688 0.781,0.885 0.385,0.198 10 false A58 0.583,2.74 0.969,2.938 0.385,0.198 10 false IG2

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the A58 yaw rate and acceleration sensor (airbag ECU assembly) connector.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait at least 60 seconds.


g.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-21 (IG2) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly))


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (E TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (E TERMINAL)
a.
C239271E36
0.25,0.708 0.75,0.958 0.5,0.25 1.26,2.688 1.635,2.208 true 2.146,2.688 1.792,2.198 true 0.188,0.26 0.5,0.458 0.313,0.198 10 false *a 0.365,0.74 0.76,0.938 0.396,0.198 10 false A58 1.167,2.708 1.479,2.906 0.313,0.198 10 false E1 2.094,2.74 2.406,2.938 0.313,0.198 10 false E2

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-25 (E1) - Body ground Always Below 1 Ω
A58-26 (E2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag ECU Assembly))


Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (E CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the A58 yaw rate and acceleration sensor (airbag ECU assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 3 km/h (2 mph) or more for at least 10 seconds.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1381 is not output. A
DTC C1381 is output. B


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>TEST MODE PROCEDURE).




A

B