Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. DTC Detection Condition Trouble Area
C1417 Either of the following is detected:
1.

The +BS terminal voltage is 17.4 V or more for 0.8 seconds or more.

2.

When voltage at terminal +BS is 17.4 V or higher, power supply voltage of master cylinder pressure sensor is cut for 0.2 seconds or more.


·

Charging system

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector

·

ABS NO. 2 fuse

·

Battery



WIRING DIAGRAM

C307645E27
0.417,0.948 1.354,1.146 0.938,0.198 10 false from Battery 1.719,1.177 2.583,1.375 0.865,0.198 10 false ABS NO. 2 3.698,2.146 4.875,2.375 1.177,0.229 10 false Skid Control ECU 3.958,3.198 5.719,3.417 1.76,0.219 10 false Brake Actuator Assembly 2.833,0.875 3.177,1.063 0.344,0.188 10 false 38 2.833,2.167 3.177,2.354 0.344,0.188 10 false 25 3.156,2.156 3.563,2.344 0.406,0.188 10 false GND1 3.135,0.875 3.542,1.063 0.406,0.188 10 false +BS 5.292,1.448 6.396,1.802 1.104,0.354 10 false Master Cylinder Pressure Sensor 3.542,3.198 3.885,3.385 0.344,0.188 10 false A71

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY

OK

2.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

2.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)

OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1417 is not output A
DTC C1417 is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B