Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch.

The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. DTC Detection Condition Trouble Area
C1425 When voltage at terminal +BS is 9.5 to 17.4 V, open circuit occurs between STP terminal circuits A and B for 0.3 seconds or more.
·

STOP NO. 5 fuse

·

Stop light switch assembly

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C376337E02
0.604,0.896 2,1.281 1.396,0.385 10 false from Stop Light Switch Assembly 0.76,1.604 2.146,1.844 1.385,0.24 10 false to Stop Light Circuit 2.76,1.792 3.74,2.021 0.979,0.229 10 false STOP NO. 2 4.198,1.115 5.177,1.344 0.979,0.229 10 false STOP NO. 5 5.052,1.031 5.281,1.25 0.229,0.219 10 false B 3.979,1.042 4.208,1.26 0.229,0.219 10 false A 5.26,0.938 5.719,1.146 0.458,0.208 10 false STP 5.271,2.208 5.771,2.417 0.5,0.208 10 false GND1 4.99,0.823 5.25,1.042 0.26,0.219 10 false 35 4.99,2.073 5.25,2.292 0.26,0.219 10 false 25 5.208,2.948 5.563,3.146 0.354,0.198 10 false A71 5.208,3.135 6.76,3.521 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that all the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)

NG

5.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.READ VALUE USING GTS (STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

In accordance with the display on the GTS, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch assembly / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


g.

Check that the stop light switch assembly condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
3.RECONFIRM DTC

b.

Turn the ignition switch to ON.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1425 is not output A
DTC C1425 is output B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

4.CHECK TERMINAL VOLTAGE (STP TERMINAL)
a.
C306843E26
1.469,0.146 1.99,0.396 0.521,0.25 1.469,0.135 1.99,0.385 0.521,0.25 2.021,1.823 2.208,1.313 true 0.125,0.052 0.438,0.25 0.313,0.198 10 false *a 1.604,0.188 1.99,0.385 0.385,0.198 10 false A71 1.854,1.854 2.24,2.052 0.385,0.198 10 false STP

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A71-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
A71-35 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

5.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

6.CHECK TERMINAL VOLTAGE (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

6.CHECK TERMINAL VOLTAGE (STP TERMINAL)

OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the A71 skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1425 is not output A
DTC C1425 is output B


HINT:

If the lighting system is normal but the DTC is still output, replace the skid control ECU (brake actuator assembly) (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (w/ Brake pedal Load Sensing Switch)>REMOVAL).




A

B

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)