Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › 2017.01–2019.08
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.

DTC No. DTC Detection Condition Trouble Area
C1432 Steering angle sensor power supply malfunction signal is received from steering angle sensor.
·

ECU-B NO. 3 fuse

·

ECU-IG1 NO. 3 fuse

·

Steering angle sensor (Spiral with sensor cable sub-assembly)

·

Wire harness or connector



WIRING DIAGRAM

C274776E62
0.823,0.667 1.292,0.865 0.469,0.198 10 false CANL 6.042,0.667 6.51,0.865 0.469,0.198 10 false CANL 0.792,1.25 1.26,1.448 0.469,0.198 10 false CANH 6.052,1.271 6.521,1.469 0.469,0.198 10 false CANH 0.906,1.948 1.375,2.146 0.469,0.198 10 false BAT 0.948,2.635 1.333,2.833 0.385,0.198 10 false IG1 1.302,0.479 1.563,0.677 0.26,0.198 10 false 3 0.896,3.292 1.281,3.49 0.385,0.198 10 false ESS 1.302,1.073 1.563,1.271 0.26,0.198 10 false 4 1.292,1.833 1.552,2.031 0.26,0.198 10 false 6 1.292,2.5 1.552,2.698 0.26,0.198 10 false 5 1.292,3.177 1.552,3.375 0.26,0.198 10 false 2 5.719,0.5 5.979,0.698 0.26,0.198 10 false 10 5.729,1.094 5.99,1.292 0.26,0.198 10 false 22 3.927,1.938 4.875,2.156 0.948,0.219 10 false from Battery 3.917,2.615 4.99,2.854 1.073,0.24 10 false from IG Circuit 2.208,2.115 3.219,2.344 1.01,0.229 10 false ECU-B NO. 3 2.219,2.813 3.396,3.042 1.177,0.229 10 false ECU-IG1 NO. 3 5.51,4 7.115,4.385 1.604,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 5.521,3.802 5.958,3.99 0.438,0.188 10 false A71 0.167,3.906 0.604,4.094 0.438,0.188 10 false J71 0.167,4.083 2.313,4.49 2.146,0.406 10 false Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly) 2.927,4.365 4.74,4.594 1.813,0.229 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral with sensor cable subassembly.

·

When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>U0073).

·

When any of the speed sensors or the yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 has trouble, DTCs for the steering angle sensor (spiral with sensor cable subassembly) may be output even when the steering angle sensor (spiral with sensor cable sub-assembly) is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (yaw rate sensor)*1 or yaw rate and acceleration sensor (airbag ECU assembly)*2 first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).

*1: w/o Airbag System

*2: w/ Airbag System




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE CIRCUIT)
a.

Turn the ignition switch off.


b.
C371519E03
0.24,0.906 0.667,1.125 0.427,0.219 1.771,1.719 2.135,1.302 true 2.823,1.656 2.417,1.302 true 0.156,0.156 0.469,0.354 0.313,0.198 10 false *a 0.323,0.927 0.635,1.125 0.313,0.198 10 false J71 1.646,1.75 1.958,1.948 0.313,0.198 10 false IG1 2.854,1.604 3.219,1.802 0.365,0.198 10 false BAT

Remove the steering wheel and the column cover.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the J71 steering angle sensor (spiral with sensor cable sub-assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J71-6 (BAT) - Body ground Always 11 to 14 V
J71-5 (IG1) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.
C371519E04
0.323,0.917 0.75,1.135 0.427,0.219 1.125,1.708 1.354,1.302 true 0.135,0.146 0.448,0.344 0.313,0.198 10 false *a 0.417,0.938 0.729,1.135 0.313,0.198 10 false J71 0.958,1.729 1.313,1.927 0.354,0.198 10 false ESS

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J71-2 (ESS) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly))


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)