Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  C144F  Brake Booster Pressure Sensor Correlation  


DESCRIPTION

The No. 1 vacuum booster pressure sensor (vacuum sensor assembly) and No. 2 vacuum booster pressure sensor (vacuum sensor assembly) detect pressure in the brake booster.

When a malfunction occurs in the difference between the input voltage values of the No. 1 brake booster pressure sensor (vacuum sensor assembly) and No. 2 brake booster pressure sensor (vacuum sensor assembly), the fail-safe prohibits ABS and brake pressure increase function control and illuminates the ABS warning light.

HINT:

EBD control will continue to the extent that EBD control is possible even after ABS is prohibited.


DTC No. DTC Detection Condition Trouble Area
C144F Either of the following is detected:
·

When the input voltages of the No. 1 brake booster pressure sensor and No. 2 brake booster pressure sensor are below 1.46 V or exceed 3.34 V, the input voltage difference between the No. 1 brake booster pressure sensor and No. 2 brake booster pressure sensor exceeds 0.41 V for 10 seconds or longer continuously.

·

When the input voltages of the No. 1 brake booster pressure sensor and No. 2 brake booster pressure sensor exceed 1.46 V or are less than 3.34 V, the input voltage difference between the No. 1 brake booster pressure sensor and No. 2 brake booster pressure sensor exceeds 0.344 V for 10 seconds or longer continuously.


·

Vacuum booster pressure sensor1 (Vacuum Sensor Assembly)

·

Vacuum booster pressure sensor2 (Vacuum Sensor Assembly)

·

Wire harness or connector

·

Vacuum hoses



WIRING DIAGRAM

Refer to DTCs C144C, C144D, C145A, C1476, C1477 and/or C1479 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C144C).

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


HINT:

When DTCs C144C, C144D, C145A, C1476, C1477 and/or C1479 is output together with DTC C144F, inspect and repair the trouble areas indicated by DTC DTCs C144C, C144D, C145A, C1476, C1477 and/or C1479 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>C144C).


PROCEDURE

1.INSPECT VACUUM HOSES
a.

Disconnect the 2 vacuum hoses from the vacuum sensor assembly.


b.

Check the vacuum hoses for cracks or damage.

OK:

There are no cracks or damage.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

REPLACE VACUUM HOSE

2.RECONFIRM DTC
a.

Reconnect the 2 vacuum hoses to the vacuum sensor assembly.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a drive test and braking test. (Depress the brake pedal to decelerate the vehicle)



Result:
Result Proceed to
DTC C144F is not output A
DTC C144F is output B



A

B