Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) › 2017.01–2018.07
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356878 ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)  TS and CG Terminal Circuit  


DESCRIPTION

The signal check circuit detects trouble in the sensor or switch signal which cannot be detected by the DTC check.

Connecting terminals TS and CG of the DLC3 starts the check.

WIRING DIAGRAM

C173350E30
0.958,0.885 1.271,1.083 0.313,0.198 10 false TS 6.042,0.885 6.354,1.083 0.313,0.198 10 false TS 0.469,2.917 0.781,3.115 0.313,0.198 10 false J45 1.25,0.781 1.563,0.979 0.313,0.198 10 false 12 1.271,1.667 1.583,1.865 0.313,0.198 10 false 4 5.698,0.771 6.01,0.969 0.313,0.198 10 false 24 0.469,3.094 0.99,3.292 0.521,0.198 10 false DLC3 5.469,2.844 5.99,3.042 0.521,0.198 10 false A71 5.458,3.042 7.115,3.448 1.656,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 0.927,1.75 1.24,1.948 0.313,0.198 10 false CG

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM(w/ Brake pedal Load Sensing Switch)>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TS of DLC3)
a.

Turn the ignition switch off.


b.

Disconnect the A71 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A71-24 (TS) - J45-12 (TS) Always Below 1 Ω
A71-24 (TS) or J45-12 (TS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TS of DLC3 - BODY GROUND)
a.
C245481E39
0.094,1.344 0.5,1.552 0.406,0.208 1.813,1.885 1.625,1.885 1.625,1.885 1.625,1.5 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.865,1.802 2.177,2 0.313,0.198 10 false TS 0.177,1.365 0.49,1.563 0.313,0.198 10 false J45

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J45-12 (TS) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of DLC3


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR