These solenoids turn on when signals are received from the skid control ECU and control the pressure acting on the wheel cylinders to control the braking force.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C0226/21 | When IG terminal voltage is 9.5 to 18.5V, an open or short in the SFRH or SFRR solenoid circuit continues for 0.05 seconds or more. | ·
Brake actuator assembly ·
SFRH or SFRR solenoid circuit ·
Skid control ECU |
| C0236/22 | When IG terminal voltage is 9.5 to 18.5V, an open or short in the SFLH or SFLR solenoid circuit continues for 0.05 seconds or more. | ·
Brake actuator assembly ·
SFLH or SFLR solenoid circuit ·
Skid control ECU |
| C0246/23 | When IG terminal voltage is 9.5 to 18.5V, an open or short in the SRRH or SRRR solenoid circuit continues for 0.05 seconds or more. | ·
Brake actuator assembly ·
SRRH or SRRR solenoid circuit ·
Skid control ECU |
| C0256/24 | When IG terminal voltage is 9.5 to 18.5V, an open or short in the SRLH or SRLR solenoid circuit continues for 0.05 seconds or more. | ·
Brake actuator assembly ·
SRLH or SRLR solenoid circuit ·
Skid control ECU |
| C1225/25 | When IG terminal voltage is 9.5 to 18.5V, an open or short in the SMCF or SMCR solenoid circuit continues for 0.05 seconds or more. | ·
Brake actuator assembly ·
SMCF or SMCR solenoid circuit ·
Skid control ECU |
| C1227/27 | When IG terminal voltage is 9.5 to 18.5V, an open or short in the SRCF or SRCR solenoid circuit continues for 0.05 seconds or more. | ·
Brake actuator assembly ·
SRCF or SRCR solenoid circuit ·
Skid control ECU |
When C0278/11 and/or C0279/12 is output together with C0226/21, C0236/22, C0246/23, C0256/24, and/or C1227/27, inspect and repair the trouble areas indicated by C0278/11 and/or C0279/12 first (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>C0278/11).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Disconnect the brake actuator connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-4 (BS) - R1-12 (SFLH) | 25°C (77°F) | 8.3 to 9.3 Ω |
| R1-12 (SFLH) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-6 (SFLR) | 25°C (77°F) | 4.0 to 4.6 Ω |
| R1-6 (SFLR) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-11 (SFRH) | 25°C (77°F) | 8.3 to 9.3 Ω |
| R1-11 (SFRH) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-5 (SFRR) | 25°C (77°F) | 4.0 to 4.6 Ω |
| R1-5 (SFRR) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-10 (SRLH) | 25°C (77°F) | 8.3 to 9.3 Ω |
| R1-10 (SRLH) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-4 (SRLR) | 25°C (77°F) | 4.0 to 4.6 Ω |
| R1-4 (SRLR) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-9 (SRRH) | 25°C (77°F) | 8.3 to 9.3 Ω |
| R1-9 (SRRH) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-3 (SRRR) | 25°C (77°F) | 4.0 to 4.6 Ω |
| R1-3 (SRRR) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-2 (SRCF) | 25°C (77°F) | 6.2 to 6.8 Ω |
| R1-2 (SRCF) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-7 (SRCR) | 25°C (77°F) | 6.2 to 6.8 Ω |
| R1-7 (SRCR) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-1 (SMCF) | 25°C (77°F) | 8.3 to 9.3 Ω |
| R1-1 (SMCF) - Body ground | Always | 10 kΩ or higher |
| R2-4 (BS) - R1-8 (SMCR) | 25°C (77°F) | 8.3 to 9.3 Ω |
| R1-8 (SMCR) - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected
(Brake Actuator) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-8 (SFLH) - R1-12 (SFLH) | Always | Below 1 Ω |
| A47-8 (SFLH) - Body ground | Always | 10 kΩ or higher |
| A47-13 (SFLR) - R1-6 (SFLR) | Always | Below 1 Ω |
| A47-13 (SFLR) - Body ground | Always | 10 kΩ or higher |
| A47-14 (SFRH) - R1-11 (SFRH) | Always | Below 1 Ω |
| A47-14 (SFRH) - Body ground | Always | 10 kΩ or higher |
| A47-15 (SFRR) - R1-5 (SFRR) | Always | Below 1 Ω |
| A47-15 (SFRR) - Body ground | Always | 10 kΩ or higher |
| A47-1 (SRLH) - R1-10 (SRLH) | Always | Below 1 Ω |
| A47-1 (SRLH) - Body ground | Always | 10 kΩ or higher |
| A47-2 (SRLR) - R1-4 (SRLR) | Always | Below 1 Ω |
| A47-2 (SRLR) - Body ground | Always | 10 kΩ or higher |
| A47-7 (SRRH) - R1-9 (SRRH) | Always | Below 1 Ω |
| A47-7 (SRRH) - Body ground | Always | 10 kΩ or higher |
| A47-26 (SRRR) - R1-3 (SRRR) | Always | Below 1 Ω |
| A47-26 (SRRR) - Body ground | Always | 10 kΩ or higher |
| A47-25 (SRCF) - R1-2 (SRCF) | Always | Below 1 Ω |
| A47-25 (SRCF) - Body ground | Always | 10 kΩ or higher |
| A47-12 (SRCR) - R1-7 (SRCR) | Always | Below 1 Ω |
| A47-12 (SRCR) - Body ground | Always | 10 kΩ or higher |
| A47-9 (SMCF) - R1-1 (SMCF) | Always | Below 1 Ω |
| A47-9 (SMCF) - Body ground | Always | 10 kΩ or higher |
| A47-10 (SMCR) - R1-8 (SMCR) | Always | Below 1 Ω |
| A47-10 (SMCR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the skid control ECU connector.
Reconnect the brake actuator connectors.
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.
Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs (C0226/21, C0236/22, C0246/23, C0256/24 and/or C1227/27) are not output | A |
| DTCs (C0226/21, C0236/22, C0246/23, C0256/24 and/or C1227/27) are output | B |
If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU and brake actuator assembly. Make sure that no DTCs are output.
If any DTCs are output while jiggling a connector or wire harness of the skid control ECU and brake actuator assembly, inspect and repair the connector or wire harness.
It is suspected that the DTCs were output due to a bad connection of the connector terminal.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B