Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C0278/11  Open in ABS Solenoid Relay Circuit  C0279/12  Short to B+ in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid.

The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by self diagnosis performed when the vehicle starts running.

HINT:

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.


DTC Code DTC Detection Condition Trouble Area
C0278/11 When either of the following is detected:
1.

IG1 terminal voltage is 9.5 to 18.5 V, and when the relay is ON, the relay contact is OFF for 0.2 seconds or more.

2.

IG1 terminal voltage 9.5 V or less due to turning the relay ON, and the relay contact is not ON for 0.2 seconds or more.


·

ABS SOL relay

·

ABS SOL relay circuit

·

Skid control ECU


C0279/12 Immediately after the ignition switch is turned to ON, the solenoid relay contact is ON for 0.2 seconds or more when the relay is OFF.
·

ABS SOL relay

·

ABS SOL relay circuit

·

Skid control ECU



WIRING DIAGRAM

Refer to DTCs C0226/21, C0236/22, C0246/23, C0256/24 and C1227/27 (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>C0226/21).

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT ABS SOLENOID RELAY (ABS SOL)
a.
C144829E13
0.138,0.102 0.344,0.295 0.206,0.193 10 *1

Remove the ABS SOL relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Apply the battery voltage between terminals 1 and 2 Below 1 Ω

Text in Illustration
*1 ABS SOL Relay



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK (POWER SOURCE TERMINAL)

NG

REPLACE ABS SOLENOID RELAY (ABS SOL)

2.INSPECT NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK (POWER SOURCE TERMINAL)
a.
C375222E01
0.167,0.115 0.479,0.313 0.313,0.198 10 false *1 0.885,2.167 1.198,2.365 0.313,0.198 10 false *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
ABS SOL relay terminal 5 - Body ground Always 11 to 14 V

Text in Illustration
*1 No. 2 Engine Room Relay Block and Junction Block
*2 ABS SOL Relay



Result:
Proceed to
OK
NG



OK

3.INSPECT BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.INSPECT BRAKE ACTUATOR ASSEMBLY
a.
C215677E07
2.438,1.958 2.167,2.531 true 2.979,2.552 2.656,1.948 true 0.125,0.104 0.396,0.323 0.271,0.219 10 false *1 2.917,2.615 3.24,2.823 0.323,0.208 10 false BS 2.031,2.615 2.354,2.823 0.323,0.208 10 false AST

Disconnect the brake actuator connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (BS) - 5(AST) Always Below 1 Ω
5 (AST) - Body ground Always 10 kΩ or higher

Text in Illustration
*1 Component without harness connected
(Brake Actuator)



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK)

NG

REPLACE BRAKE ACTUATOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-4 (BS) - ABS SOL relay terminal 3 Always Below 1 Ω
R2-4 (BS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE ACTUATOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE ACTUATOR)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-11 (AST) - R2-5 (AST) Always Below 1 Ω
A47-11 (AST) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - NO. 2 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-21 (R+) - ABS SOL relay terminal 2 Always Below 1 Ω
A50-21 (R+) - Body ground Always 10 kΩ or higher
A50-7 (SR) - ABS SOL relay terminal 1 Always Below 1 Ω
A50-7 (SR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Install the ABS SOL relay.


c.

Reconnect the skid control ECU connectors.


d.

Reconnect the brake actuator connectors.



f.

Start the engine.


g.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


h.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

HINT:

Reinstall the relays, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


Result:
Result Proceed to
DTCs (C0278/11 and/or C0279/12) are not output A
DTCs (C0278/11 and/or C0279/12) are output B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU and brake actuator assembly. Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU and brake actuator assembly, inspect and repair the connector or wire harness.

·

It is suspected that the DTCs were output due to a bad connection of the connector terminal.





A

B

REPLACE SKID CONTROL ECU