Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C1241/41  Low Battery Positive Voltage  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU stores this DTC and the fail safe function prohibits ABS operation.

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.

The DTC is canceled when the IG1 terminal voltage returns to normal.

DTC Code DTC Detection Condition Trouble Area
C1241/41 When any of the following is detected:
1.

At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is 9.5 V or less for 10 seconds or more.

2.

When IG1 terminal voltage is 9.5 V or less, the detection condition for an open in the solenoid relay or motor relay is met.


·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of the skid control ECU



WIRING DIAGRAM

C375076E01
0.771,1.094 2.25,1.354 1.479,0.26 10 false from IG1-NO. 1 Relay 3.823,1.271 4.885,1.521 1.063,0.25 10 false ECU-IG1 NO. 3 5.615,0.875 5.854,1.115 0.24,0.24 10 false 10 6,1.083 6.406,1.344 0.406,0.26 10 false IG1 5.625,1.906 5.865,2.146 0.24,0.24 10 false 11 5.99,2.125 6.51,2.354 0.521,0.229 10 false GND1 5.615,2.469 5.854,2.708 0.24,0.24 10 false 22 5.99,2.698 6.49,2.927 0.5,0.229 10 false GND2 5.677,3.052 5.917,3.292 0.24,0.24 10 false 2 5.99,3.292 6.563,3.521 0.573,0.229 10 false GND3 5.615,3.646 5.854,3.885 0.24,0.24 10 false 13 5.99,3.865 6.531,4.083 0.542,0.219 10 false GND4 5.802,5.063 6.948,5.281 1.146,0.219 10 false Skid Control ECU 5.583,1.094 5.917,1.354 0.333,0.26 10 false A50 5.594,2.125 5.927,2.385 0.333,0.26 10 false A50 5.583,2.688 5.917,2.948 0.333,0.26 10 false A50 5.583,3.281 5.917,3.542 0.333,0.26 10 false A50 5.573,3.875 5.906,4.135 0.333,0.26 10 false A50

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT SKID CONTROL ECU (IG1 TERMINAL)

NG

CHECK OR REPLACE CHARGING SYSTEM OR BATTERY

2.INSPECT SKID CONTROL ECU (IG1 TERMINAL)
a.
C215683E05
1.573,0.865 1.958,1.094 0.385,0.229 2.313,1.583 2.563,0.99 2.563,0.99 2.74,0.99 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 1.646,0.896 1.958,1.094 0.313,0.198 10 false A50 2.823,0.906 3.135,1.104 0.313,0.198 10 false IG1

Disconnect the skid control ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A50-10 (IG1) - Body ground Ignition switch ON 11 to 14 V

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



Result:
Proceed to
OK
NG



OK

3.INSPECT SKID CONTROL ECU (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

3.INSPECT SKID CONTROL ECU (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-11 (GND1) - Body ground Always Below 1 Ω
A50-22 (GND2) - Body ground Always Below 1 Ω
A50-2 (GND3) - Body ground Always Below 1 Ω
A50-13 (GND4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the skid control ECU connectors.



d.

Drive the vehicle at the speed of 3 km/h (2 mph) or more for 10 seconds or more.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1241/41) is not output A
DTC (C1241/41) is output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE SKID CONTROL ECU