Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C1246/46  Master Cylinder Pressure Sensor Malfunction  C1281/81  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  


DESCRIPTION

DTC C1281/81 can be deleted when the master cylinder pressure sensor sends a master cylinder pressure signal or the Test Mode ends. DTC C1281/81 is output only in the Test Mode.

DTC Code DTC Detection Condition Trouble Area
C1246/46 When any of the following is detected:
1.

When IG1 terminal voltage is 9.5 to 18.5 V, VCM terminal voltage is not between 4.7 and 5.3 V for 1.2 seconds or more.

2.

PMC terminal voltage is not between 0.14 and 4.75 V for 1.2 seconds or more.

3.

With the stop light switch off, either of the following continues for 5 seconds or more:

-

PMC voltage is 0.86 V or more.

-

PMC voltage is less than 0.3 V.


4.

At a vehicle speed of 7 km/h (4.3 mph) or more and PMC terminal voltage is 0.86V or more, PMC terminal voltage does not change by 0.01 V or more for 30 seconds or more.

5.

Noise occurs in PMC terminal voltage at least 7 times for 5 seconds.


·

Master cylinder pressure sensor

·

Master cylinder pressure sensor circuit

·

Stop light switch circuit

·

Skid control ECU


C1281/81 Detected only during Test Mode.
·

Stop light switch

·

Master cylinder pressure sensor



WIRING DIAGRAM

C375077E01
1.042,1.052 1.5,1.25 0.458,0.198 10 false VCM 1.042,1.594 1.5,1.792 0.458,0.198 10 false PMC 1.167,2.083 1.625,2.281 0.458,0.198 10 false E2 1.521,0.938 1.74,1.156 0.219,0.219 10 false 3 1.521,1.417 1.771,1.656 0.25,0.24 10 false 2 1.521,1.917 1.74,2.177 0.219,0.26 10 false 1 0.313,2.896 0.771,3.094 0.458,0.198 10 false F14 0.292,3.094 2.427,3.365 2.135,0.271 10 false Master Cylinder Pressure Sensor 0.302,4.073 1.313,4.302 1.01,0.229 10 false from Battery 1.979,4.25 2.875,4.469 0.896,0.219 10 false STOP NO. 1 2.979,3.948 3.188,4.177 0.208,0.229 10 false 1 4.49,3.948 4.688,4.177 0.198,0.229 10 false 2 3.135,4.563 3.594,4.76 0.458,0.198 10 false H1 3.125,4.74 4.375,4.99 1.25,0.25 10 false Stop Light Switch 4.698,4.229 5.635,4.448 0.938,0.219 10 false STOP NO. 5 5.813,3.844 6.042,4.073 0.229,0.229 10 false 9 5.958,5.177 7.094,5.406 1.135,0.229 10 false Skid Control ECU 6.167,4.073 6.625,4.271 0.458,0.198 10 false STP 6.167,2.552 6.625,2.75 0.458,0.198 10 false PSS 6.167,2.063 6.625,2.26 0.458,0.198 10 false E2 6.156,1.563 6.615,1.76 0.458,0.198 10 false PMC 6.177,1.073 6.635,1.271 0.458,0.198 10 false VCM 5.823,0.844 6.052,1.073 0.229,0.229 10 false 3 5.74,1.063 6.198,1.26 0.458,0.198 10 false A48 5.792,1.354 6.125,1.573 0.333,0.219 10 false 11 5.833,1.833 6.083,2.104 0.25,0.271 10 false 4 5.781,2.354 6.083,2.563 0.302,0.208 10 false 12 5.74,4.073 6.104,4.281 0.365,0.208 10 false A50 3.25,2.771 4,3.01 0.75,0.24 10 false Shielded 5.74,1.573 6.198,1.771 0.458,0.198 10 false A48 5.74,2.063 6.198,2.26 0.458,0.198 10 false A48 5.74,2.573 6.198,2.771 0.458,0.198 10 false A48

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

INSPECT STOP LIGHT CIRCUIT

2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List mode on the GTS (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DATA LIST / ACTIVE TEST).

ABS / VSC / TRC:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-



d.

Check that the stop light display observed on the GTS changes when the brake pedal is depressed.

OK:

When the brake pedal is depressed, the GTS displays "ON".



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

9.INSPECT SKID CONTROL ECU (STP TERMINAL)
3.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Select the Data List mode on the GTS (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DATA LIST / ACTIVE TEST).

ABS / VSC / TRC:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Sensor 1 Master cylinder pressure sensor 1 reading / min.: 0.00 V, max.: 4.99 V When brake pedal is released: 0.3 to 0.7 V Reading increases when brake pedal is depressed



b.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, voltage displayed on the GTS increases.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - MASTER CYLINDER PRESSURE SENSOR)
4.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

At a speed of 10 km/h (6 mph) or more, drive the vehicle and perform braking test (decelerate the vehicle by depressing the brake pedal).



Result:
Result Proceed to
DTC (C1246/46) is not output A
DTC (C1246/46) is output B



A

B

REPLACE SKID CONTROL ECU

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - MASTER CYLINDER PRESSURE SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU connector.


c.

Disconnect the master cylinder pressure sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A48-3 (VCM) - F14-3 (VCM) Always Below 1 Ω
A48-3 (VCM) or F14-3 (VCM) - Body ground Always 10 kΩ or higher
A48-11 (PMC) - F14-2 (PMC) Always Below 1 Ω
A48-11 (PMC) or F14-2 (PMC) - Body ground Always 10 kΩ or higher
A48-4 (E2) - F14-1 (E2) Always Below 1 Ω
A48-4 (E2) or F14-1 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT SKID CONTROL ECU (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SKID CONTROL ECU (SENSOR INPUT)
a.
C215678E08
1.354,0.948 1.781,1.198 0.427,0.25 1.656,2.25 1.656,1.542 true 0.156,0.094 0.396,0.313 0.24,0.219 10 false *a 1.448,0.99 1.854,1.188 0.406,0.198 10 false A48 1.417,2.292 2.042,2.5 0.625,0.208 10 false 3 (VCM)

Reconnect the skid control ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A48-3 (VCM) - Body ground Ignition switch ON 4.75 to 5.25 V

Text in Illustration
*a Component with harness connected
(Skid Control ECU)



Result:
Proceed to
OK
NG



OK

7.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPLACE SKID CONTROL ECU

7.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.

Turn the ignition switch off.


b.

Reconnect the master cylinder pressure sensor connector.


c.

Install the hydro LSPV gauge (SST) and bleed air.


d.

Start the engine.


e.
C215678E09
1.354,0.948 1.781,1.198 0.427,0.25 1.656,2.229 1.656,1.625 true 0.156,0.094 0.396,0.313 0.24,0.219 10 false *a 1.448,0.99 1.854,1.188 0.406,0.198 10 false A48 1.396,2.292 2.104,2.5 0.708,0.208 10 false 11 (PMC)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Fluid Pressure MPa (kgf/cm2 , psi) Specified Condition
A48-11 (PMC) - Body ground 0 (0, 0) 0.47 to 0.53 V
9.8 (100, 1422) 2.37 to 2.63 V
19.6 (200, 2844) 4.27 to 4.73 V

Text in Illustration
*a Component with harness connected
(Skid Control ECU)


NOTICE:

Check the master cylinder pressure sensor signal after replacement



Result:
Proceed to
OK
NG



OK

8.RECONFIRM DTC

NG

REPLACE MASTER CYLINDER PRESSURE SENSOR

8.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

At a speed of 10 km/h (6 mph) or more, drive the vehicle and perform braking test (decelerate the vehicle by depressing the brake pedal).



Result:
Result Proceed to
DTC (C1246/46) is not output A
DTC (C1246/46) is output B



A

B

REPLACE SKID CONTROL ECU

9.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.
C215683E06
1.521,0.865 1.906,1.094 0.385,0.229 2.156,1.563 2.156,0.688 2.156,0.688 2.292,0.688 true 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 1.604,0.896 1.917,1.094 0.313,0.198 10 false A50 2.375,0.604 2.781,0.854 0.406,0.25 10 false STP

Turn the ignition switch off.


b.

Disconnect the skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A50-9 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V
A50-9 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 2 V

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)