Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  C1249/49  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU inputs the stop light switch signal and the condition of brake operation.

The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line while the stop light switch is OFF.

DTC Code DTC Detection Condition Trouble Area
C1249/49 When IG1 terminal voltage is 9.5 to 18.5 V, an open circuit of the stop light switch continues for 0.3 seconds or more.
·

Stop light switch

·

Stop light switch circuit

·

Skid control ECU



WIRING DIAGRAM

C395229E01
0.406,0.729 1.854,1 1.448,0.271 10 false from IG1-NO. 1 Relay 0.094,1.479 0.938,1.719 0.844,0.24 10 false from Battery 2.896,0.885 4,1.146 1.104,0.26 10 false ECU-IG1 NO. 3 4.948,0.5 5.26,0.698 0.313,0.198 10 false 10 4.917,0.729 5.292,0.938 0.375,0.208 10 false A50 5.333,0.719 5.708,0.938 0.375,0.219 10 false IG1 5.333,1.49 5.677,1.688 0.344,0.198 10 false STP 5,1.25 5.229,1.448 0.229,0.198 10 false 9 4,1.625 4.906,1.865 0.906,0.24 10 false STOP NO. 5 3.979,2.021 4.885,2.26 0.906,0.24 10 false STOP NO. 2 3.385,1.333 3.583,1.542 0.198,0.208 10 false 2 2.479,1.354 2.688,1.563 0.208,0.208 10 false 1 1.51,1.635 2.375,1.854 0.865,0.219 10 false STOP NO. 1 2.406,1.781 2.719,1.979 0.313,0.198 10 false H1 1.802,2.51 2,2.719 0.198,0.208 10 false 1 2.021,2.51 2.333,2.708 0.313,0.198 10 false E 2.76,2.51 3.115,2.74 0.354,0.229 10 false STP 3.146,2.51 3.344,2.708 0.198,0.198 10 false 4 2.344,2.865 2.813,3.115 0.469,0.25 10 false STOP 1.938,3.281 3.625,3.552 1.688,0.271 10 false Rear Combination Light LH 1.781,4.156 1.969,4.344 0.188,0.188 10 false 1 2.052,4.167 2.365,4.365 0.313,0.198 10 false E 2.74,4.167 3.104,4.354 0.365,0.188 10 false STP 3.156,4.167 3.406,4.365 0.25,0.198 10 false 4 2.344,4.51 2.896,4.708 0.552,0.198 10 false STOP 1.948,4.938 3.719,5.219 1.771,0.281 10 false Rear Combination Light RH 1.104,5.948 1.302,6.167 0.198,0.219 10 false 2 1.313,5.958 1.531,6.177 0.219,0.219 10 false E 2.917,5.948 3.104,6.146 0.188,0.198 10 false B 3.167,5.948 3.396,6.135 0.229,0.188 10 false 1 1.531,6.438 2.958,6.708 1.427,0.271 10 false High Mount Stop Light 1.271,6.448 1.583,6.646 0.313,0.198 10 false n1 1.625,3.281 1.938,3.479 0.313,0.198 10 false U11 1.615,4.948 1.927,5.146 0.313,0.198 10 false U10 4.958,5.604 5.271,5.802 0.313,0.198 10 false 11 5.333,5.833 5.875,6.052 0.542,0.219 10 false GND1 5.333,6.385 5.833,6.604 0.5,0.219 10 false GND2 5.333,6.948 5.896,7.167 0.563,0.219 10 false GND3 5.333,7.51 5.885,7.76 0.552,0.25 10 false GND4 4.958,7.271 5.271,7.469 0.313,0.198 10 false 13 5.01,6.719 5.323,6.917 0.313,0.198 10 false 2 4.969,6.167 5.281,6.365 0.313,0.198 10 false 22 5.563,8.406 6.708,8.615 1.146,0.208 10 false Skid Control ECU 4.917,1.479 5.292,1.688 0.375,0.208 10 false A50 4.938,5.833 5.313,6.042 0.375,0.208 10 false A50 4.938,6.396 5.313,6.604 0.375,0.208 10 false A50 4.927,6.948 5.302,7.156 0.375,0.208 10 false A50 4.917,7.5 5.292,7.708 0.375,0.208 10 false A50 2.667,1.771 3.906,1.99 1.24,0.219 10 false Stop Light Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop light comes on when the brake pedal is depressed, and goes off when the brake pedal is released.


OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF


Result:
Proceed to
OK
NG



OK

2.INSPECT SKID CONTROL ECU (STP TERMINAL)

NG

6.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)
2.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.
C215683E07
1.521,0.865 1.906,1.094 0.385,0.229 2.156,1.563 2.385,0.74 2.385,0.74 2.521,0.74 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.604,0.896 1.917,1.094 0.313,0.198 10 false A50 2.615,0.656 3.021,0.906 0.406,0.25 10 false STP

Disconnect the skid control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A50-9 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 8 to 14 V
A50-9 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 2 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)


Result:
Proceed to
OK
NG



OK

3.INSPECT SKID CONTROL ECU (IG1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

3.INSPECT SKID CONTROL ECU (IG1 TERMINAL)
a.
C215683E05
1.573,0.865 1.958,1.094 0.385,0.229 2.313,1.583 2.563,0.99 2.563,0.99 2.74,0.99 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 1.646,0.896 1.958,1.094 0.313,0.198 10 false A50 2.823,0.906 3.135,1.104 0.313,0.198 10 false IG1

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A50-10 (IG1) - Body ground Ignition switch ON 11 to 14 V

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



Result:
Proceed to
OK
NG



OK

4.INSPECT SKID CONTROL ECU (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

4.INSPECT SKID CONTROL ECU (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-11 (GND1) - Body ground Always Below 1 Ω
A50-22 (GND2) - Body ground Always Below 1 Ω
A50-2 (GND3) - Body ground Always Below 1 Ω
A50-13 (GND4) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1249/49) is not output A
DTC (C1249/49) is output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE SKID CONTROL ECU

6.INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)
a.
C375100E01
0.49,1.042 0.813,1.26 0.323,0.219 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 0.573,1.063 0.885,1.26 0.313,0.198 10 false H1

Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H1-1 - Body ground Always 11 to 14 V

Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch)



Result:
Proceed to
OK
NG



OK

7.INSPECT STOP LIGHT SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

7.INSPECT STOP LIGHT SWITCH
a.
C375102E01
0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.375,2.698 0.688,2.896 0.313,0.198 10 false *b 1.031,2.688 1.344,2.885 0.313,0.198 10 false *c

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch pin free Below 1 Ω
1 - 2 Switch pin pushed in 10 kΩ or higher

Text in Illustration
*a Component without harness connected
(Stop Light Switch)
*b Free
*c Pushed in



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)

NG

REPLACE STOP LIGHT SWITCH

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT SWITCH)
a.

Disconnect the skid control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-9 (STP) - H1-2 Always Below 1 Ω
A50-9 (STP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.


b.

Reconnect the stop light switch connector.



d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is recorded (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1249/49) is not output A
DTC (C1249/49) is output B


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).




A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

B

REPLACE SKID CONTROL ECU