Home › Engine / Hybrid System › 2TR-FE EXHAUST › EXHAUST PIPE(for Standard Body)
RM2850E _51 Engine / Hybrid System _073296 2TR-FE EXHAUST _0356990 EXHAUST PIPE(for Standard Body) A

2TR-FE EXHAUST  EXHAUST PIPE(for Standard Body)  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.634 in.)

If the length is not as specified, replace the compression spring.



b.
A104635E01
2.518,0.953 2.759,0.953 false 1.509,1.641 2.111,1.452 false 2.765,0.757 3.335,1.141 0.570,0.384 10 Wooden Block 0.884,1.534 1.404,1.748 0.520,0.214 10 Gasket

Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not reuse the exhaust pipe gasket.

·

Do not push in the gasket with the exhaust pipe when connecting it.




c.
A161045

Install the front exhaust pipe assembly with the 2 compression springs and the 2 bolts.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 17460 3.INSTALL CATALYTIC WITH PIPE CONVERTER ASSEMBLY

a.
A161044E03
0.313,1.771 0.49,1.958 0.177,0.188 10 true *1 0.781,1.771 0.948,1.938 0.167,0.167 10 true *1 2.438,0.604 2.688,0.823 0.25,0.219 10 true *2 3.01,0.604 3.219,0.823 0.208,0.219 10 true *2

Install a new gasket onto the front exhaust pipe assembly.


b.

Install the catalytic with pipe converter assembly with the 2 new nuts.(*2)

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf) for nut



c.

Tighten the 2 bolts and the 2 new nuts.(*1)

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf) for bolt



Hide 17420 5.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

For rear exhaust type

i.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.634 in.)

If the length is not as specified, replace the compression spring.



ii.

Install a new gasket onto the catalytic with pipe converter assembly.


iii.
A178347E02
0.563,0.396 0.719,0.542 0.156,0.146 10 false *1 0.563,1 0.771,1.167 0.208,0.167 10 true *1 2.542,0.427 2.719,0.615 0.177,0.188 10 true *2 1.896,0.417 2.073,0.615 0.177,0.198 10 true *2 0.646,0.198 0.854,0.365 0.208,0.167 10 true *1

Install the center exhaust pipe assembly with the 2 new nuts.(*2)

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf) for nut



iv.

Tighten the 2 bolts and 2 compression spring.(*1)

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf) for bolt




b.

For side exhaust type

i.

Install a new gasket onto the front exhaust pipe assembly.


ii.
A178348E02
0.333,1.833 0.51,2.052 0.177,0.219 10 true *1 0.781,1.854 0.927,2.031 0.146,0.177 10 true *1 2.438,0.635 2.635,0.823 0.198,0.188 10 true *2 3.052,0.594 3.26,0.802 0.208,0.208 10 true *2

Install the center exhaust pipe assembly with the 2 new nuts.(*1)

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf) for nut



iii.

Tighten the 2 bolts and the 2 new nuts.(*2)

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf) for bolt




Hide 17404 6.INSTALL NO. 1 TAIL EXHAUST PIPE ASSEMBLY

a.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.634 in.)

If the length is not as specified, replace the compression spring.



b.

Install a new gasket onto the center exhaust pipe assembly.


c.
A431302

Install the No. 1 tail exhaust pipe assembly with the 2 new nuts and the bolt.

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf) for nut


Torque:

23 N*m (234 kgf*cm, 17 ft.*lbf) for bolt



d.
A431299

Tighten the 2 bolts and the 2 compression springs.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf) for bolt



Hide 17430 7.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A104634

Using a vernier caliper, measure the free length of the compression spring.

Minimum length:

41.5 mm (1.634 in.)

If the length is not as specified, replace the compression spring.



b.

Install a new gasket onto the center exhaust pipe assembly.


c.
A178349E04
1.302,0.135 1.51,0.333 0.208,0.198 10 true *1 0.313,0.198 0.542,0.385 0.229,0.188 10 true *1 1.125,1.74 1.333,1.948 0.208,0.208 10 false *2 1.833,0.469 2.01,0.688 0.177,0.219 10 true *2 2.458,0.49 2.635,0.656 0.177,0.167 10 true *2

Install the tail exhaust pipe assembly with the 2 new nuts and the bolt.

Torque:

19 N*m (194 kgf*cm, 14 ft.*lbf) for nut


Torque:

23 N*m (234 kgf*cm, 17 ft.*lbf) for bolt



d.

Tighten the 2 bolts and 2 compression springs.

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf) for bolt



Hide 17430 8.INSTALL NO. 2 TAIL EXHAUST PIPE ASSEMBLY

a.
A431298

Install a new gasket onto the No. 1 tail exhaust pipe assembly.


b.

Install the No. 2 tail exhaust pipe assembly with the bolt.

Torque:

23 N*m (234 kgf*cm, 17 ft.*lbf)



c.
A431297

Tighten the 2 bolts and the 2 nuts

Torque:

43 N*m (438 kgf*cm, 32 ft.*lbf)



Hide 9.INSPECT FOR EXHAUST GAS LEAK