Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0100  Mass or Volume Air Flow Circuit  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter sub-assembly measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and provide a proper air-fuel ratio. Inside the mass air flow meter sub-assembly, there is a heated platinum wire exposed to the flow of intake air.

By applying a specific current to the wire, the ECM heats this wire to a given temperature. The flow of incoming air cools the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components* in the mass air flow meter sub-assembly. The voltage level is proportional to the air flow through the sensor. The ECM interprets this voltage as the intake air amount.

HINT:

*: The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the set temperature.

When any of these DTCs are set, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine rpm and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A158493E02
1.854,1.406 1.479,0.271 false 2.26,1 2.083,1.417 false 4.417,1.427 3.719,1.885 3.719,1.885 3.719,2.094 true 4.729,1.375 5.271,2.198 5.271,2.198 5.271,2.385 true 0.198,0.156 1.458,0.51 1.26,0.354 10 false Temperature Sensor (Thermistor) 3.281,2.094 4.542,2.448 1.26,0.354 10 false Temperature Sensor (Thermistor) 2.104,0.229 2.344,0.427 0.24,0.198 10 false B+ 2.125,0.594 3.417,0.76 1.292,0.167 10 false Power Transistor 2.323,0.865 3.49,1.229 1.167,0.365 10 false Platinum Hot Wire (Heater) 4.667,2.406 6.448,2.625 1.781,0.219 10 false Platinum Hot Wire (Heater) 1.615,1.333 1.74,1.531 0.125,0.198 10 false A 2.25,1.333 2.406,1.531 0.156,0.198 10 false B 2.865,1.458 3.823,1.646 0.958,0.188 10 false Output Voltage

DTC No. DTC Detection Condition Suspected Area
P0100 When mass air flow meter sub-assembly circuit is open or shorted for more than 3 seconds
(1 trip detection logic)
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

ECM


P0102 When mass air flow meter sub-assembly circuit is open for more than 3 seconds
(1 trip detection logic)
·

Open in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

Short in ground circuit

·

ECM


P0103 When mass air flow meter sub-assembly circuit is shorted for more than 3 seconds
(1 trip detection logic)
·

Short in mass air flow meter sub-assembly circuit (+B circuit)

·

Mass air flow meter sub-assembly

·

ECM



MONITOR DESCRIPTION

If there is a defect in the mass air flow meter sub-assembly or an open or short circuit, the voltage level will deviate outside the normal operating range. The ECM interprets this deviation as a defect in the mass air flow meter sub-assembly and sets a DTC.

Example:

When the sensor voltage output is less than 0.2 V or more than 4.9 V and if either condition continues more than 3 seconds.

This monitor runs for 3 seconds (the first 3 seconds of engine idle) after the engine is started (1 trip detection logic).

HINT:

When DTC P0100, P0102 or P0103 is detected, check the air flow ratio by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / MAF.

Air Flow Value (g/sec.) Malfunction
Approximately 0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


271.0 or more Open in E2G circuit


WIRING DIAGRAM

A395984E01
0.667,0.875 0.917,1.073 0.25,0.198 10 false P/I 0.458,1.708 1.323,1.906 0.865,0.198 10 false R/B NO. 2-B 0.458,2.281 1.063,2.458 0.604,0.177 10 false FL MAIN 0.646,3.021 1.25,3.198 0.604,0.177 10 false Battery 1.875,1.719 3.365,1.906 1.49,0.188 10 false NO. 2 Integration Relay 1.125,0.719 1.375,0.917 0.25,0.198 10 false 2E 1.719,1.49 1.969,1.688 0.25,0.198 10 false 2D 2.875,1.063 3.125,1.26 0.25,0.198 10 false 2D 2.875,0.719 3.125,0.917 0.25,0.198 10 false 2D 5.417,1.031 5.708,1.229 0.292,0.198 10 false B75 5.417,1.531 5.708,1.729 0.292,0.198 10 false B75 5.417,2.802 5.74,3 0.323,0.198 10 false A55 1.417,0.844 2.094,1.021 0.677,0.177 10 false EFI-MAIN 2.24,1.417 2.531,1.594 0.292,0.177 10 false EFI 1.156,0.531 1.333,0.719 0.177,0.188 10 false 1 2.906,0.531 3.083,0.719 0.177,0.188 10 false 4 2.906,0.896 3.083,1.083 0.177,0.188 10 false 2 1.51,1.469 1.688,1.656 0.177,0.188 10 false 3 3.656,0.594 3.833,0.781 0.177,0.188 10 false 1 3.865,0.615 4.115,0.813 0.25,0.198 10 false +B 4.688,1.417 5.021,1.615 0.333,0.198 10 false E2G 4.75,0.917 5,1.115 0.25,0.198 10 false VG 3.844,1.927 4.177,2.125 0.333,0.198 10 false B51 3.844,2.094 5.156,2.448 1.313,0.354 10 false Mass Air Flow Meter Sub-assembly 5.76,0.917 6.01,1.115 0.25,0.198 10 false VG 5.76,1.417 6.083,1.604 0.323,0.188 10 false E2G 5.75,2.688 6.198,2.875 0.448,0.188 10 false MREL 6.146,3.271 6.594,3.458 0.448,0.188 10 false ECM 5.073,0.917 5.25,1.104 0.177,0.188 10 false 3 5.083,1.427 5.26,1.615 0.177,0.188 10 false 2 5.448,0.833 5.698,1.031 0.25,0.198 10 false 28 5.448,1.344 5.698,1.542 0.25,0.198 10 false 30 5.479,2.604 5.625,2.802 0.146,0.198 10 false 8

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (MASS AIR FLOW RATE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


e.

Read the values.

Result:
Mass Air Flow Rate (g/sec.) Proceed To
0.0 A
271.0 or more B
Between 0.0 and 271.0* C


HINT:

*: The value must change when the throttle valve is opened or closed.




A

2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE)

B

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

C

2.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (POWER SOURCE)
a.
A148358E22
1.49,0.917 1.948,1.177 0.458,0.26 1.344,2.042 0.927,2.49 true 0.146,0.115 0.406,0.323 0.26,0.208 10 false *a 0.781,2.531 1.073,2.729 0.292,0.198 10 false +B 1.594,0.979 1.938,1.167 0.344,0.188 10 false B51

Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B51-1 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass air flow meter sub-assembly)


Result:
Proceed To
OK
NG



OK

3.INSPECT ECM (VG VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)
3.INSPECT ECM (VG VOLTAGE)
a.
A146289E40
1.146,0.177 1.542,0.417 0.396,0.24 1.552,1.01 1.25,1.771 true 2.104,1.781 1.677,1 true 0.99,1.802 1.656,2.01 0.667,0.208 10 false 30 (E2G) 2.042,1.813 2.615,2 0.573,0.188 10 false 28 (VG) 1.219,0.208 1.5,0.385 0.281,0.177 10 false B75 0.146,0.094 0.427,0.271 0.281,0.177 10 false *a

Start the engine.


b.

Measure the voltage of the ECM connector.

HINT:

The A/C switch should be turned OFF.


Standard Voltage:
Tester Connection Condition Specified Condition
B75-28 (VG) - B75-30 (E2G) Engine is idling 0.5 to 3.0 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed To
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-3 (VG) - B75-28 (VG) Always Below 1 Ω
B51-2 (E2G) - B75-30 (E2G) Always Below 1 Ω
B51-3 (VG) or B75-28 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-1 (+B) - 2D-4 Always Below 1 Ω
B51-1 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the resistance of the ECM connector.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-2 (E2G) - Body ground Always Below 1 Ω



Result:
Proceed To
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-3 (VG) - B75-28 (VG) Always Below 1 Ω
B51-2 (E2G) - B75-30 (E2G) Always Below 1 Ω
B51-3 (VG) or B75-28 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR