Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0110  Intake Air Temperature Circuit  P0112  Intake Air Temperature Circuit Low Input  P0113  Intake Air Temperature Circuit High Input  


DESCRIPTION

A429919E01
1.604,1.99 1.875,1.5 1.875,1.5 2.021,1.5 true 0.052,0.458 1.042,0.698 0.99,0.24 10 false Resistance kΩ 2.115,1.396 2.906,1.635 0.792,0.24 10 false Acceptable 1.292,4.208 2.542,4.427 1.25,0.219 10 false Temperature °C (°F) 0.563,0.771 0.875,0.969 0.313,0.198 10 false 30 0.563,0.948 0.875,1.146 0.313,0.198 10 false 20 0.563,1.24 0.875,1.438 0.313,0.198 10 false 10 0.635,1.542 0.948,1.74 0.313,0.198 10 false 5 0.635,1.781 0.948,1.979 0.313,0.198 10 false 3 0.635,1.979 0.948,2.177 0.313,0.198 10 false 2 0.625,2.271 0.938,2.469 0.313,0.198 10 false 1 0.521,2.583 0.833,2.781 0.313,0.198 10 false 0.5 0.521,2.813 0.833,3.01 0.313,0.198 10 false 0.3 0.521,2.99 0.833,3.188 0.313,0.198 10 false 0.2 0.51,3.313 0.823,3.51 0.313,0.198 10 false 0.1 0.823,3.677 1.135,3.875 0.313,0.198 10 false -20 0.823,3.865 1.135,4.063 0.313,0.198 10 false (-4) 1.219,3.688 1.531,3.885 0.313,0.198 10 false 0 1.135,3.865 1.448,4.063 0.313,0.198 10 false (32) 1.521,3.688 1.833,3.885 0.313,0.198 10 false 20 1.479,3.865 1.792,4.063 0.313,0.198 10 false (68) 1.844,3.688 2.156,3.885 0.313,0.198 10 false 40 1.771,3.865 2.188,4.063 0.417,0.198 10 false (104) 2.177,3.688 2.49,3.885 0.313,0.198 10 false 60 2.115,3.865 2.594,4.083 0.479,0.219 10 false (140) 2.521,3.688 2.833,3.885 0.313,0.198 10 false 80 2.458,3.865 2.885,4.094 0.427,0.229 10 false (176) 2.792,3.688 3.135,3.885 0.344,0.198 10 false 100 2.792,3.865 3.208,4.094 0.417,0.229 10 false (212)

The Intake Air Temperature (IAT) sensor is built into the mass air flow (MAF) meter sub-assembly, and monitors the intake air temperature. The IAT sensor has a built-in thermistor that varies its resistance depending on the temperature of the intake air. When the air temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. The variations in resistance are communicated to the ECM as changes in voltage (see figure 1).

The IAT sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the IAT sensor from terminal THA via resistor R.

Resistor R and the IAT sensor are connected in series. When the resistance value of the IAT sensor changes in accordance with changes in the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability during cold engine operation.

DTC No. DTC Detection Condition Trouble Area
P0110 Open or short in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0112 Short in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM


P0113 Open in intake air temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in intake air temperature sensor circuit

·

Intake air temperature sensor (built into mass air flow meter sub-assembly)

·

ECM



HINT:

When DTC P0110, P0112 or P0113 is detected, check the intake air temperature by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or more Short circuit


MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to calculate the IAT. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the IAT sensor and sets a DTC.

Example:

When the sensor voltage output is -40°C (-40°F) (P0113) or more than 140°C (284°F) (P0112) and if either condition continues for 0.5 seconds or more.

This monitor runs for 0.5 seconds after the ignition switch is turned to ON (1 trip detection logic).

WIRING DIAGRAM

A401741E02
0.5,1.896 0.958,2.094 0.458,0.198 10 false B51 0.5,2.042 3,2.417 2.5,0.375 10 false Intake Air Temperature Sensor (Built into Mass Air Flow Meter Sub-assembly) 1.708,0.656 2.042,0.833 0.333,0.177 10 false THA 1.802,1.188 2.073,1.385 0.271,0.198 10 false E2 2.135,0.646 2.333,0.844 0.198,0.198 10 false 4 2.125,1.198 2.365,1.375 0.24,0.177 10 false 5 4.833,0.583 5.031,0.76 0.198,0.177 10 false 29 4.792,0.76 5.125,0.958 0.333,0.198 10 false B75 4.823,1.115 5.021,1.292 0.198,0.177 10 false 28 4.792,1.302 5.125,1.5 0.333,0.198 10 false B73 5.156,0.667 5.479,0.865 0.323,0.198 10 false THA 5.156,1.188 5.406,1.385 0.25,0.198 10 false E2 6.094,0.208 6.427,0.458 0.333,0.25 10 false 5 V 6.177,0.594 6.448,0.792 0.271,0.198 10 false R 5.813,2.25 6.219,2.448 0.406,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


e.

Read the value displayed on the GTS.

Result:
Result Proceed To
-40°C (-40°F) A
140°C (284°F) or higher B
Same as actual intake air temperature C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or higher.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A127961E81
0.344,3.26 0.802,3.531 0.458,0.271 1.583,4.01 1.885,3.479 true 2.385,4 2.094,3.458 true 0.771,1.688 1.01,1.885 0.24,0.198 10 false *1 2.667,1.719 2.896,1.896 0.229,0.177 10 false *2 2.469,1.021 2.802,1.177 0.333,0.156 10 false THA 2.448,1.5 2.698,1.667 0.25,0.167 10 false E2 0.448,3.323 0.75,3.5 0.302,0.177 10 false B51 1.365,4.021 1.75,4.208 0.385,0.188 10 false THA 2.302,4.021 2.573,4.208 0.271,0.188 10 false E2 0.156,2.281 0.333,2.458 0.177,0.177 10 false *a 1.792,1.385 1.948,1.563 0.156,0.177 10 false 5 1.792,1.031 1.948,1.208 0.156,0.177 10 false 4

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter sub-assembly wire harness side connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


g.

Read the value displayed on the GTS.

Standard value:

140°C (284°F) or higher


Text in Illustration
*1 Mass Air Flow Meter Sub-assembly
*2 ECM
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


Result:
Proceed To
OK
NG



OK

CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-4 (THA) - B75-29 (THA) Always Below 1 Ω
B51-5 (E2) - B75-28 (E2) Always Below 1 Ω



Result:
Proceed To
OK
NG



OK

CONFIRM GOOD CONNECTION AT ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
a.
A186168E22
1.396,0.594 1.781,0.844 0.385,0.25 2.635,1.729 2.865,1.906 0.229,0.177 10 false *2 0.75,1.698 0.979,1.885 0.229,0.188 10 false *1 2.458,1.51 2.708,1.688 0.25,0.177 10 false E2 2.448,1.042 2.792,1.219 0.344,0.177 10 false THA 1.458,0.625 1.802,0.802 0.344,0.177 10 false B51

Disconnect the mass air flow meter sub-assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.


f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)


Text in Illustration
*1 Mass Air Flow Meter Sub-assembly
*2 ECM


Result:
Proceed To
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B51-4 (THA) or B75-29 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR