Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0115  Engine Coolant Temperature Circuit  P0117  Engine Coolant Temperature Circuit Low Input  P0118  Engine Coolant Temperature Circuit High Input  


DESCRIPTION

A thermistor is built into the Engine Coolant Temperature sensor and changes its resistance value according to the engine coolant temperature.

The structure of the sensor and its connection to the ECM is the same as that of the intake air temperature sensor and its connection.

HINT:

If the ECM detects DTC P0115, P0117 or P0118, the ECM enters fail-safe mode in which the engine coolant temperature is assumed to be 80°C (176°F).


DTC No. DTC Detection Condition Suspected Area
P0115 Open or short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open or short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0117 Short in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Short in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM


P0118 Open in engine coolant temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
·

Open in engine coolant temperature sensor circuit

·

Engine coolant temperature sensor

·

ECM



HINT:

When DTC P0115, P0117 or P0118 is detected, check the engine coolant temperature by selecting the following menu items on the GTS: Powertrain / Engine and ECT / Data List / Coolant Temp.

Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or more Short circuit


MONITOR DESCRIPTION

The engine coolant temperature sensor is used to monitor the engine coolant temperature. The engine coolant temperature sensor has a thermistor that varies its resistance depending on the temperature of the engine coolant. When the coolant temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. The variations in resistance are reflected in the voltage output from the sensor. The ECM monitors the sensor voltage and uses this value to calculate the engine coolant temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a fault in the engine coolant temperature sensor and sets a DTC.

Example:

When the ECM calculates that the engine coolant temperature is -40°C (-40°F) (P0118) or more than 140°C (284°F) (P0117) and that either condition continues for 0.5 seconds or more, the ECM will set a DTC.

This monitor runs for 0.5 seconds after the ignition switch is turned to ON (1 trip detection logic).

WIRING DIAGRAM

A401742E02
1.979,0.615 2.375,0.802 0.396,0.188 10 false THW 2.115,1.229 2.396,1.417 0.281,0.188 10 false E2 2.438,0.604 2.635,0.802 0.198,0.198 10 false 2 2.438,1.229 2.635,1.427 0.198,0.198 10 false 1 0.677,1.896 1.01,2.073 0.333,0.177 10 false B57 0.677,2.063 2.979,2.24 2.302,0.177 10 false Engine Coolant Temperature Sensor 5.25,0.625 5.5,0.802 0.25,0.177 10 false 32 5.25,1.229 5.458,1.417 0.208,0.188 10 false 28 5.531,0.604 5.99,0.802 0.458,0.198 10 false THW 5.531,1.219 5.854,1.427 0.323,0.208 10 false E2 6.24,0.26 6.552,0.51 0.313,0.25 10 false 5 V 5.729,2.26 6.073,2.458 0.344,0.198 10 false B73 6.135,2.26 6.542,2.458 0.406,0.198 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

If DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


e.

Read the value displayed on the GTS.

Standard value:

Between 75 and 100°C (167 and 212°F) with warm engine


Result:
Result Proceed To
-40°C (-40°F) A
140°C (284°F) or higher B
Between 75 and 100°C (167 and 212°F) C


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F) or more.





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)

C

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
a.
A403000E01
0.354,3.427 0.771,3.698 0.417,0.271 2.396,1.323 2.771,1.5 0.375,0.177 10 false THW 2.396,1.677 2.667,1.875 0.271,0.198 10 false E2 2.594,2.26 2.865,2.458 0.271,0.198 10 false *2 0.719,2.125 0.99,2.323 0.271,0.198 10 false *1 1.583,1.177 1.75,1.365 0.167,0.188 10 false 2 1.573,1.833 1.74,2.021 0.167,0.188 10 false 1 0.281,2.75 0.552,2.948 0.271,0.198 10 false *a 0.438,3.49 0.74,3.688 0.302,0.198 10 false B57

Disconnect the engine coolant temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine coolant temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


g.

Read the value displayed on the GTS.

Standard value:

140°C (284°F) or higher


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM
*a Front view of wire harness connector
(to Engine Coolant Temperature Sensor)


Result:
Proceed To
OK
NG



OK

CONFIRM GOOD CONNECTION AT SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B57-2 (THW) - B73-32 (THW) Always Below 1 Ω
B57-1 (E2) - B73-28 (E2) Always Below 1 Ω



Result:
Proceed To
OK
NG



OK

CONFIRM GOOD CONNECTION AT ECM. IF OK, REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR OPEN IN ECM)
a.
A164746E28
1.375,0.646 1.802,0.917 0.427,0.271 2.469,1.51 2.708,1.688 0.24,0.177 10 false E2 2.469,1.031 2.833,1.208 0.365,0.177 10 false THW 1.448,0.698 1.76,0.865 0.313,0.167 10 false B57 2.604,1.729 2.854,1.958 0.25,0.229 10 false *2 0.729,1.729 0.99,1.927 0.26,0.198 10 false *1

Disconnect the engine coolant temperature sensor connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


f.

Read the value displayed on the GTS.

Standard value:

-40°C (-40°F)


Text in Illustration
*1 Engine Coolant Temperature Sensor
*2 ECM


Result:
Proceed To
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine coolant temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B57-2 (THW) or B73-32 (THW) - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR