Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0136  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)  


DESCRIPTION

HINT:

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.


In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a TWC is used. For the most efficient use of the TWC, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. To help the ECM to deliver accurate air-fuel ratio control, a heated oxygen sensor is used.

The heated oxygen sensor is located behind the TWC, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with the heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).

When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. less than 0.45 V).

Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-TWC air-fuel ratio is rich (high voltage, i.e. more than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.

The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air-fuel ratio after the TWC is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A088111E53
1.292,2.26 1.073,2.26 false 3.156,0.688 3.323,0.688 false 2.521,0.021 3.792,0.25 1.271,0.229 10 false Atmospheric Air 3.385,0.594 4.031,0.792 0.646,0.198 10 false Housing 3.292,1.5 4.5,1.698 1.208,0.198 10 false Platinum Electrode 3.292,1.76 3.823,1.958 0.531,0.198 10 false Heater 3.292,2.021 4.458,2.219 1.167,0.198 10 false Coating (Ceramic) 1.927,2.51 2.792,2.708 0.865,0.198 10 false Exhaust Gas 1.344,2.177 1.771,2.375 0.427,0.198 10 false Cover 5.458,0.104 6.865,0.302 1.406,0.198 10 false Ideal Air-fuel Mixture 4.708,2.26 6.667,2.427 1.958,0.167 10 false Richer - Air-fuel Ratio - Leaner 4.354,0.281 5.313,0.479 0.958,0.198 10 false Output Voltage 3.25,1.052 4.385,1.417 1.135,0.365 10 false Solid Electrolyte (Zirconia Element)

DTC No. DTC Detection Conditions Trouble Areas
P0136 While vehicle driving with warmed engine, heated oxygen sensor (bank 1 sensor 2) output does not switch from RICH to LEAN or from LEAN to RICH.
(2 trip detection logic)
·

Open or short in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

ECM



WIRING DIAGRAM

A395985E01
0.625,0.698 1.313,0.875 0.688,0.177 10 false EFI-MAIN 0.406,1.594 0.646,1.771 0.24,0.177 10 false 2E 2.26,0.552 2.5,0.729 0.24,0.177 10 false 2D 2.26,0.979 2.5,1.156 0.24,0.177 10 false 2D 2.26,1.427 2.5,1.604 0.24,0.177 10 false 2D 5.406,0.552 5.719,0.74 0.313,0.188 10 false B73 5.406,1.323 5.688,1.51 0.281,0.188 10 false B73 5.406,2.01 5.708,2.198 0.302,0.188 10 false B73 5.406,3.104 5.708,3.292 0.302,0.188 10 false A55 0.583,2.094 0.875,2.271 0.292,0.177 10 false P/I 0.594,2.573 1.479,2.76 0.885,0.188 10 false R/B NO. 2-B 0.76,3.708 1.646,3.896 0.885,0.188 10 false Battery 0.583,3.052 1.469,3.24 0.885,0.188 10 false FL MAIN 0.979,1.792 2.5,2 1.521,0.208 10 false NO. 2 Integration Relay 1.51,1.292 1.854,1.479 0.344,0.188 10 false EFI 0.688,1.563 0.844,1.74 0.156,0.177 10 false 1 2.302,0.375 2.458,0.552 0.156,0.177 10 false 4 2.302,0.792 2.458,0.969 0.156,0.177 10 false 2 2.302,1.24 2.458,1.417 0.156,0.177 10 false 3 3.573,0.427 3.729,0.604 0.156,0.177 10 false 2 3.583,1.188 3.74,1.365 0.156,0.177 10 false 4 4.646,0.438 4.802,0.615 0.156,0.177 10 false 1 3.792,0.438 4.042,0.604 0.25,0.167 10 false +B 4.156,1.167 4.563,1.354 0.406,0.188 10 false OX1B 3.792,1.188 4.042,1.354 0.25,0.167 10 false E2 4.156,0.438 4.563,0.625 0.406,0.188 10 false HT1B 5.76,3.104 6.229,3.292 0.469,0.188 10 false MREL 5.75,1.875 6.01,2.063 0.26,0.188 10 false E2 5.75,1.198 6.156,1.385 0.406,0.188 10 false OX1B 5.75,0.438 6.156,0.625 0.406,0.188 10 false HT1B 4.635,1.208 4.792,1.385 0.156,0.177 10 false 3 3.406,1.667 4.927,1.875 1.521,0.208 10 false Heated Oxygen Sensor 3.396,1.521 3.708,1.688 0.313,0.167 10 false A62 5.479,0.354 5.635,0.531 0.156,0.177 10 false 2 5.469,1.135 5.698,1.313 0.229,0.177 10 false 25 5.448,1.813 5.677,1.99 0.229,0.177 10 false 28 5.49,2.917 5.635,3.094 0.146,0.177 10 false 8 6.177,3.885 6.604,4.083 0.427,0.198 10 false ECM 3.792,3.75 4.74,3.948 0.948,0.198 10 false *: Shielded 5.094,1.677 5.271,1.813 0.177,0.135 10 false *

CONFIRMATION DRIVING PATTERN

A128472E05
0.598,0.696 1.548,0.859 0.95,0.163 10 Vehicle Speed 0.421,1.65 1.546,1.813 1.125,0.163 10 Ignition Switch off 0.894,2.168 1.564,2.331 0.67,0.163 10 (a) to (e) 0.444,1.182 1.607,1.402 1.163,0.22 10 40 km/h (29 mph) 1.643,1.746 1.256,2.141 false 1.693,2.047 2.448,2.356 0.755,0.309 10 60 seconds or more 2.785,2.047 3.541,2.356 0.755,0.309 10 10 seconds or more 3.696,2.047 4.451,2.356 0.755,0.309 10 10 seconds or more 5.022,2.047 5.778,2.356 0.755,0.309 10 10 seconds or more 5.798,1.824 6.197,1.995 0.4,0.17 10 Time 2.051,0.436 3.186,0.745 1.135,0.309 10 Once 40 seconds or more 3.208,0.436 4.342,0.745 1.135,0.309 10 Twice 40 seconds or more 4.541,0.436 6.064,0.745 1.523,0.309 10 Ten times 40 seconds or more 5.308,1.522 5.52,1.685 0.212,0.163 10 (h) 4.864,1.272 5.075,1.435 0.212,0.163 10 (g) 3.989,1.536 4.201,1.699 0.212,0.163 10 (h) 1.698,1.464 2.075,1.627 0.377,0.163 10 Idling 2.107,1.464 2.319,1.627 0.212,0.163 10 (f) 2.605,1.272 2.817,1.435 0.212,0.163 10 (g) 3.063,1.536 3.274,1.699 0.212,0.163 10 (h) 3.52,1.272 3.732,1.435 0.212,0.163 10 (g)

NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.


HINT:

This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.


(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON and turn the tester on.

(d) Switch the ECM from normal mode to check mode (Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE).

(e) Start the engine.

(f) Allow the engine to idle for 60 seconds.

(g) Drive the vehicle at a vehicle speed of more than 40 km/h (29 mph) for 40 seconds or more.

(h) Allow the engine to idle for 10 seconds or more.

(i) Repeat steps (g) and (h) described above at least 10 times.


CAUTION / NOTICE / HINT

HINT:

GTS only:

Malfunctioning areas can be identified by performing the A/F Control function provided in the Active Test. The A/F Control function can help to determine whether the Air-fuel Ratio (A/F) sensor, heated oxygen (HO2) sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the A/F control operation using the GTS

1.

Connect the GTS to the DLC3.

2.

Start the engine and turn the GTS ON.

3.

Warm up the engine at an engine speed of 2,500 rpm for approximately 90 seconds.

4.

On the tester, select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

5.

Perform the A/F Control operation with the engine in an idling condition (press the right or left button to change the fuel injection volume).

6.

Monitor the output voltage of the A/F and heated oxygen sensors (AFS B1 S1 and O2S B1 S2) displayed on the tester.



HINT:
·

The A/F Control operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Standard:
Tester Display
(Sensor)
Injection Volume Status Voltage
AFS B1 S1
(A/F)
+25% Rich Less than 3.0 V
AFS B1 S1
(A/F)
-12.5% Lean More than 3.35 V
O2S B1 S2
(HO2)
+25% Rich More than 0.55 V
O2S B1 S2
(HO2)
-12.5% Lean Less than 0.4 V


NOTICE:

The A/F sensor output has a few seconds of delay and the heated oxygen sensor output has about 20 seconds of delay at maximum.


A430115E01
5.792,3.74 6.792,3.948 1,0.208 10 false - A/F sensor 3.667,4.927 4.531,5.104 0.865,0.177 8 false Less than 0.4 V 3.208,4.396 4.333,4.615 1.125,0.219 10 false Output Voltage 3.25,3.365 4.542,3.615 1.292,0.25 10 false Injection Volume 3.229,1.292 4.521,1.542 1.292,0.25 10 false Injection Volume 3.24,2.313 4.333,2.521 1.094,0.208 10 false Output Voltage 0.625,1.292 1.917,1.542 1.292,0.25 10 false Injection Volume 0.625,3.365 1.917,3.615 1.292,0.25 10 false Injection Volume 0.594,5.438 1.885,5.688 1.292,0.25 10 false Injection Volume 0.604,7.49 1.896,7.74 1.292,0.25 10 false Injection Volume 3.25,7.49 4.542,7.74 1.292,0.25 10 false Injection Volume 3.25,5.438 4.542,5.688 1.292,0.25 10 false Injection Volume 0.635,2.302 1.823,2.51 1.188,0.208 10 false Output Voltage 0.625,4.396 1.792,4.646 1.167,0.25 10 false Output Voltage 0.552,6.479 1.719,6.729 1.167,0.25 10 false Output Voltage 0.573,8.563 1.74,8.813 1.167,0.25 10 false Output Voltage 3.24,8.563 4.406,8.813 1.167,0.25 10 false Output Voltage 3.25,6.479 4.417,6.729 1.167,0.25 10 false Output Voltage 3.594,4.698 4.542,4.885 0.948,0.188 8 false More than 0.55 V 0.917,2.625 1.885,2.792 0.969,0.167 8 false More than 3.35 V 0.979,2.885 1.875,3.063 0.896,0.177 8 false Less than 3.0 V 1.563,1.604 1.927,1.781 0.365,0.177 8 false +25% 1.49,1.833 1.917,2.01 0.427,0.177 8 false -12.5% 3.573,2.604 4.531,2.771 0.958,0.167 8 false More than 0.55 V 3.635,2.844 4.49,3.01 0.854,0.167 8 false Less than 0.4 V 0.844,4.802 2.042,5.052 1.198,0.25 8 false Almost no reaction 0.854,8.938 2.052,9.188 1.198,0.25 8 false Almost no reaction 3.5,8.938 4.698,9.188 1.198,0.25 8 false Almost no reaction 3.49,6.865 4.688,7.115 1.198,0.25 8 false Almost no reaction 0.917,6.771 1.885,6.958 0.969,0.188 8 false More than 3.35 V 0.99,7 1.896,7.167 0.906,0.167 8 false Less than 3.0 V 0.24,2.083 0.396,2.281 0.156,0.198 10 false 1 0.24,4.25 0.396,4.448 0.156,0.198 10 false 2 0.25,6.333 0.406,6.531 0.156,0.198 10 false 3 0.24,8.417 0.396,8.615 0.156,0.198 10 false 4 0.115,0.49 0.49,0.719 0.375,0.229 10 false Case 0.635,0.573 3.063,0.771 2.427,0.198 10 false A/F Sensor (Sensor 1) Output Voltage 3.24,0.594 5.667,0.802 2.427,0.208 10 false HO2 Sensor (Sensor 2) Output Voltage 5.938,0.469 6.979,0.885 1.042,0.417 10 false Main Suspected Trouble Area 6.396,2.115 6.552,2.313 0.156,0.198 10 false - 5.802,4.135 7.073,4.333 1.271,0.198 10 false - A/F sensor heater 5.802,4.594 7.083,4.792 1.281,0.198 10 false - A/F sensor circuit 5.844,5.51 6.896,5.885 1.052,0.375 10 false - HO2 sensor 5.844,6.135 6.708,6.479 0.865,0.344 10 false - HO2 sensor heater 5.844,6.75 6.719,7.115 0.875,0.365 10 false - HO2 sensor circuit 5.823,7.51 6.594,7.698 0.771,0.188 10 false - Injector 5.813,7.844 6.969,8.177 1.156,0.333 10 false - Fuel pressure 5.802,8.24 7.094,8.948 1.292,0.708 10 false - Gas leak from exhaust system (Air-fuel ratio extremely rich or lean) 2.552,2.75 3,2.938 0.448,0.188 8 false OK 2.5,4.719 2.948,4.906 0.448,0.188 8 false NG 2.552,6.865 3,7.052 0.448,0.188 8 false OK 2.5,8.844 2.948,9.031 0.448,0.188 8 false NG 5.167,2.708 5.615,2.896 0.448,0.188 8 false OK 5.167,4.813 5.615,5 0.448,0.188 8 false OK 5.135,8.854 5.583,9.042 0.448,0.188 8 false NG 5.135,6.771 5.583,6.958 0.448,0.188 8 false NG 1.5,3.677 1.865,3.833 0.365,0.156 8 false +25% 4.083,1.594 4.427,1.781 0.344,0.188 8 false +25% 4.104,3.656 4.458,3.844 0.354,0.188 8 false +25% 1.427,3.875 1.854,4.052 0.427,0.177 8 false -12.5% 4.021,1.823 4.448,2 0.427,0.177 8 false -12.5% 4.021,3.896 4.448,4.073 0.427,0.177 8 false -12.5% 1.479,5.75 1.865,5.938 0.385,0.188 8 false +25% 1.469,7.771 1.823,7.948 0.354,0.177 8 false +25% 4.104,7.792 4.479,7.979 0.375,0.188 8 false +25% 4.167,5.729 4.531,5.896 0.365,0.167 8 false +25% 1.406,5.948 1.833,6.125 0.427,0.177 8 false -12.5% 1.396,8.01 1.823,8.188 0.427,0.177 8 false -12.5% 4.031,8.021 4.458,8.198 0.427,0.177 8 false -12.5% 4.083,5.938 4.51,6.115 0.427,0.177 8 false -12.5%

The following A/F Control procedure enables the technician to check and graph the output voltage of both A/F sensor and heated oxygen sensor.

To display the graph, select the following menu items on the tester: View / Line graph.

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check the conditions that would cause the engine to run with the rich air-fuel mixture.

·

A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check the conditions that would cause the engine to run with the lean air-fuel mixture.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P0136)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result:
Result Proceed To
P0136 is output A
P0136 and other DTCs are output B


HINT:

If any DTCs other than P0136 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1 S2.


d.

Allow the engine to run at 2,500 rpm for 3 minutes.


e.

Depress the accelerator pedal quickly until the engine rpm reaches 4,000 rpm 3 times.

Standard voltage:

The heated oxygen sensor voltage alternates between below 0.45 V and 0.6 V or more.


A128474E14
1.438,0.51 1.719,0.688 0.281,0.177 10 false 1 V 2.521,0.229 2.823,0.417 0.302,0.188 10 false OK 3.438,0.229 3.74,0.417 0.302,0.188 10 false NG 4.385,0.229 4.688,0.417 0.302,0.188 10 false NG 5.333,0.219 5.635,0.406 0.302,0.188 10 false NG 1.354,0.781 1.75,0.958 0.396,0.177 10 false 0.6 V 1.302,1.073 1.781,1.25 0.479,0.177 10 false 0.45 V 1.438,1.375 1.729,1.542 0.292,0.167 10 false 0 V


Result:
Proceed To
OK
NG



OK

3.CONFIRMATION DRIVING PATTERN

NG

5.INSPECT HEATED OXYGEN SENSOR
3.CONFIRMATION DRIVING PATTERN
HINT:

Clear all DTCs before performing the confirmation driving pattern (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).


Result:
Proceed To
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OUTPUT AGAIN)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136 OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


d.

Input DTCs: P0136.


e.

Check that the STATUS is NORMAL. If the STATUS is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.


Result:
Display (DTC Output) Proceed To
NORMAL
(No DTC output)
A
ABNORMAL
(P0136 output)
B



A

B

5.INSPECT HEATED OXYGEN SENSOR
a.

Result:
Proceed To
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 2 INTEGRATION RELAY)

NG

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 2 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor connector.


b.

Remove the NO. 2 integration relay from the NO.2 relay block and junction block assembly.


c.

Measure the resistance.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-2 (+B) - 2D-4 Always Below 1Ω
A62-2 (+B) or 2D-4 - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance.

Standard Resistance:
Tester Connections Condition Specified Conditions
B73-25 (OX1B) - A62-3 (OX1B) Always Below 1 Ω
B73-2 (HT1B) - A62-1 (HT1B) Always Below 1 Ω
B73-28 (E2) - A62-4 (E2) Always Below 1 Ω
B73-25 (OX1B) or A62-3 (OX1B) - Body ground Always 10 kΩ or higher
B73-2 (HT1B) or A62-1 (HT1B) - Body ground Always 10 kΩ or higher



Result:
Proceed To
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR